FRONT DOOR > REASSEMBLY |
| 1. INSTALL CUSHION |
![]() |
Install the cushion onto the door panel.
| 2. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() |
Slide the front door outside handle frame and engage the claw and install it.
Using a T30 "TORX" socket, install the front door outside handle frame with the screw.
| 3. INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD |
![]() |
Attach the 3 claws to install the front door outside handle front pad.
| 4. INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD |
![]() |
Attach the 2 claws to install the front door outside handle rear pad.
| 5. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Pushing the front door outside handle assembly in the direction of the arrow mark shown in the illustration, install the front door outside handle assembly.
| 6. INSTALL FRONT DOOR LOCK |
Apply MP grease to the sliding and rotating areas of the front door lock.
![]() |
Install the front door inside locking cable.
![]() |
Attach the 3 claws to close the cover.
![]() |
Install the front door lock remote control cable.
Install a new door lock wire harness seal on to the front door lock.
Insert the front door lock open rod into the front door lock, and set it to the front door outside handle frame.
Make sure that the front door lock open rod is securely connected to the front door lock.
Apply adhesive to the threads of the screws.
![]() |
Using a T30 "TORX" socket wrench, install the front door lock with the 3 screws.
| 7. INSTALL DOOR LOCK CYLINDER (for Driver Side) |
![]() |
Attach the 2 claws to install the door lock cylinder onto the front door outside handle cover.
| 8. INSTALL FRONT DOOR OUTSIDE HANDLE COVER |
![]() |
Using a T30 "TORX" socket, install the front door outside handle cover.
Install the hole plug.
| 9. INSTALL FRONT DOOR PANEL PROTECTOR |
![]() |
Attach the 8 clips to install the front door panel protector.
| 10. INSTALL FRONT DOOR WEATHERSTRIP |
![]() |
Attach the 39 clips to install the front door weatherstrip.
| 11. INSTALL FRONT DOOR CHECK ASSEMBLY |
![]() |
Apply MP grease to the sliding areas of the door check.
Install the front door check onto the door panel with the 2 nuts.
Apply adhesive to the threads of the bolt.
Install the front door check onto the body panel with the bolt.
| 12. INSTALL FRONT NO. 1 DOOR STIFFENER CUSHION |
![]() |
Attach the 2 clips to install the front No. 1 door stiffener cushion.
| 13. INSTALL FRONT DOOR FRAME REAR LOWER SUB-ASSEMBLY |
![]() |
Install the front door frame rear lower sub-assembly with the 2 bolts.
| 14. INSTALL FRONT DOOR FRAME FRONT LOWER SUB-ASSEMBLY |
![]() |
Install the front door frame front lower sub-assembly with the 2 bolts.
| 15. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Apply MP grease to the sliding and rotating areas of the front door window regulator.
![]() |
Loosely screw bolt A onto the front door window regulator
Insert the front door window regulator into the door panel. Provisionally tighten bolt A to hang the front door window regulator on the door panel.
Install the front door window regulator with the 5 bolts, and tighten bolt A.
Connect the connector.
| 16. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Insert the door glass into the door panel by the arrows in the illustration.
![]() |
Install the front door glass onto the front door window regulator with the 2 bolts.
| 17. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 18. INSTALL FRONT DOOR SERVICE HOLE COVER |
![]() |
Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.
![]() |
Attach the clamps and connect the connectors.
| 19. INSTALL FRONT DOOR NO. 1 TRIM BRACKET |
![]() |
Install the front door No. 1 trim bracket with the 2 screws.
| 20. INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side with Memory) |
![]() |
Install the outer mirror control ECU assembly with the 2 screws.
Connect the connector.
| 21. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY |
![]() |
Attach the 5 claws and clip to install a new front door glass outer weatherstrip.
| 22. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY |
![]() |
Temporarily install the mirror by inserting the claw on the mirror into the holes on the vehicle.
Tighten the 3 nuts in the sequence shown in the illustration and install the mirror.
| 23. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Attach the 3 claws.
![]() |
Install the speaker with the 4 screws.
Connect the connector.
| 24. INSTALL SIDE AIR BAG SENSOR ASSEMBLY |
Check that the ignition switch is turned off.
Check that the cable is disconnected from the battery negative (-) terminal.
![]() |
Attach the guide and install the airbag sensor with the bolt.
Confirm that there is no looseness by shaking the side airbag sensor.
Connect the airbag connector.
| 25. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP |
![]() |
Install the front door glass inner weatherstrip on the front door trim board sub-assembly and fold down the 8 claws, as shown in the illustration.
| 26. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Install the front door inside handle sub-assembly with the 3 screws.
| 27. INSTALL FRONT DOOR INSIDE HANDLE BEZEL |
![]() |
Install the front door inside handle bezel with the 4 screws.
| 28. INSTALL SEAT MEMORY SWITCH (for Driver Side with Memory) |
![]() |
Install the seat memory switch with the 2 screws.
| 29. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
Connect the connectors.
![]() |
Connect the front door lock remote control cable and the front door inside locking cable.
![]() |
Attach the 10 clips to install the front door trim board sub-assembly.
![]() |
Tighten the 2 screws.
Install the front door armrest cover.
| 30. INSTALL FRONT ARMREST BASE UPPER PANEL |
![]() |
Connect the connector.
Attach the 2 clips and 5 claws to install the front armrest base upper panel.
| 31. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Attach the 4 claws to install the front door inside handle bezel plug
| 32. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Attach the 3 clips to install the front door lower frame bracket garnish.
| 33. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH (for 14 Speakers) |
![]() |
Connect the connector.
Attach the 3 clips to install the front door lower frame bracket garnish.
| 34. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 35. CHECK SRS WARNING LIGHT |