Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR

FRONT DOOR > REASSEMBLY

for Preparation Click here



1. INSTALL CUSHION


    B190570
  1. Install the cushion onto the door panel.



2. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B195034
  1. Slide the front door outside handle frame and engage the claw and install it.

  1. Using a T30 "TORX" socket, install the front door outside handle frame with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



3. INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD


    B190566
  1. Attach the 3 claws to install the front door outside handle front pad.



4. INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD


    B190565
  1. Attach the 2 claws to install the front door outside handle rear pad.



5. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    B190564
  1. Pushing the front door outside handle assembly in the direction of the arrow mark shown in the illustration, install the front door outside handle assembly.



6. INSTALL FRONT DOOR LOCK
  1. Apply MP grease to the sliding and rotating areas of the front door lock.



    B192554
  1. Install the front door inside locking cable.



    B192553
  1. Attach the 3 claws to close the cover.



    B192551
  1. Install the front door lock remote control cable.

  1. Install a new door lock wire harness seal on to the front door lock.

  1. Insert the front door lock open rod into the front door lock, and set it to the front door outside handle frame.

  1. Make sure that the front door lock open rod is securely connected to the front door lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    B190561
  1. Using a T30 "TORX" socket wrench, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



7. INSTALL DOOR LOCK CYLINDER (for Driver Side)


    B190567
  1. Attach the 2 claws to install the door lock cylinder onto the front door outside handle cover.



8. INSTALL FRONT DOOR OUTSIDE HANDLE COVER


    B190562
  1. Using a T30 "TORX" socket, install the front door outside handle cover.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.



9. INSTALL FRONT DOOR PANEL PROTECTOR


    B190560
  1. Attach the 8 clips to install the front door panel protector.



10. INSTALL FRONT DOOR WEATHERSTRIP


    B190559
  1. Attach the 39 clips to install the front door weatherstrip.



11. INSTALL FRONT DOOR CHECK ASSEMBLY


B190558
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the front door check onto the door panel with the 2 nuts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the front door check onto the body panel with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 in.*lbf }



12. INSTALL FRONT NO. 1 DOOR STIFFENER CUSHION


    B190557
  1. Attach the 2 clips to install the front No. 1 door stiffener cushion.



13. INSTALL FRONT DOOR FRAME REAR LOWER SUB-ASSEMBLY


    B190556
  1. Install the front door frame rear lower sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



14. INSTALL FRONT DOOR FRAME FRONT LOWER SUB-ASSEMBLY


    B190555
  1. Install the front door frame front lower sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



15. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B190554E01
  1. Loosely screw bolt A onto the front door window regulator

  1. Insert the front door window regulator into the door panel. Provisionally tighten bolt A to hang the front door window regulator on the door panel.

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Install the front door window regulator with the 5 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



16. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    B192559
  1. Insert the door glass into the door panel by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.



    B190553
  1. Install the front door glass onto the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



17. INSTALL FRONT DOOR GLASS RUN


    B190552
  1. Install the front door glass run.



18. INSTALL FRONT DOOR SERVICE HOLE COVER


    B195024
  1. Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B190551
  1. Attach the clamps and connect the connectors.



19. INSTALL FRONT DOOR NO. 1 TRIM BRACKET


    B190549
  1. Install the front door No. 1 trim bracket with the 2 screws.



20. INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side with Memory)


    B192565
  1. Install the outer mirror control ECU assembly with the 2 screws.

  1. Connect the connector.



21. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


B191702
  1. Attach the 5 claws and clip to install a new front door glass outer weatherstrip.



22. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY


B190501E01
  1. Temporarily install the mirror by inserting the claw on the mirror into the holes on the vehicle.

  1. Tighten the 3 nuts in the sequence shown in the illustration and install the mirror.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



23. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


    E161076
  1. Attach the 3 claws.



    E161072
  1. Install the speaker with the 4 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.



24. INSTALL SIDE AIR BAG SENSOR ASSEMBLY
  1. Check that the ignition switch is turned off.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B194501E01
  1. Attach the guide and install the airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. Do not use a side airbag sensor that has been dropped.
    2. Do not subject the side airbag sensor to any impact or force.

  1. Confirm that there is no looseness by shaking the side airbag sensor.

  1. Connect the airbag connector.



25. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP


    B190548
  1. Install the front door glass inner weatherstrip on the front door trim board sub-assembly and fold down the 8 claws, as shown in the illustration.



26. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B190545
  1. Install the front door inside handle sub-assembly with the 3 screws.



27. INSTALL FRONT DOOR INSIDE HANDLE BEZEL


B190544
  1. Install the front door inside handle bezel with the 4 screws.



28. INSTALL SEAT MEMORY SWITCH (for Driver Side with Memory)


    B194034
  1. Install the seat memory switch with the 2 screws.



29. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connectors.



    B190543
  1. Connect the front door lock remote control cable and the front door inside locking cable.



    B190542
  1. Attach the 10 clips to install the front door trim board sub-assembly.



    B190541
  1. Tighten the 2 screws.

  1. Install the front door armrest cover.



30. INSTALL FRONT ARMREST BASE UPPER PANEL


B190537
  1. Connect the connector.

  1. Attach the 2 clips and 5 claws to install the front armrest base upper panel.



31. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B190540
  1. Attach the 4 claws to install the front door inside handle bezel plug



32. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


B194240
  1. Attach the 3 clips to install the front door lower frame bracket garnish.



33. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH (for 14 Speakers)


B190538
  1. Connect the connector.

  1. Attach the 3 clips to install the front door lower frame bracket garnish.



34. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

CAUTION:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



35. CHECK SRS WARNING LIGHT
Check the SRS warning light (Click here).