Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK

REAR DOOR LOCK > INSTALLATION

for Preparation Click here


NOTICE:
  1. If reusing a door lock that has been removed, replace the packing in the connecting part with new.
  2. Make sure that no grease or dirt adheres to the packing surface in the connecting part.



1. INSTALL REAR DOOR LOCK
  1. Apply MP grease to the sliding and rotating areas of the front door lock.



    B192550
  1. Install the rear door inside locking cable.



    B192549
  1. Attach the 3 claws to close the cover.



    B192547
  1. Install the rear door lock remote control cable.



    B192546
  1. Attach the claw to close the cover.

  1. Install a new door lock wire harness seal on to the rear door lock.



    B192117
  1. Insert the rear door lock into the rear door outside handle release plate, and set it to the rear door panel.

  1. Make sure that the rear door outside handle frame lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a T30 "TORX" socket wrench, install the rear door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B190588
  1. Install the rear door glass sub-assembly onto the rear door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



3. INSTALL REAR DOOR WINDOW FRAME REAR LOWER SUB-ASSEMBLY


B190586
  1. Install the rear door window frame rear lower sub-assembly with the nut and 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL REAR DOOR GLASS RUN


    B190585
  1. Install the rear door glass run.



5. INSTALL REAR DOOR SERVICE HOLE COVER


    B195022
  1. Apply butyl tape to the door panel, then install a new rear door service hole cover as shown in the illustration.

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B190584
  1. Attach the clamps and connect the connectors.



6. INSTALL REAR DOOR TRIM NO. 2 BRACKET


    B190583
  1. Install the rear door trim No. 2 bracket with the 2 screws.



7. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B190580
  1. Connect the rear door lock remote control cable and the rear door inside locking cable.

  1. Connect the connector.



    B190579
  1. Attach the 9 clips to install the rear door trim board sub-assembly.



    B190578
  1. Tighten the 2 screws.

  1. Install the rear door armrest cover.



8. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


B190576
  1. Attach the 4 claws to install the rear door inside handle bezel plug.



9. INSTALL REAR DOOR ARMREST BASE UPPER PANEL
  1. Connect the connector.



    B190574
  1. Attach the 2 clips and 5 claws to install the rear door armrest base upper panel.



10. INSTALL REAR DOOR FRAME GARNISH


    B190577
  1. Attach the 6 clips to install the rear door frame garnish.