Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1422/22    Compressor Lock Sensor Circuit

for Preparation Click here


DESCRIPTION

The ECM sends a engine speed signal to the air conditioning amplifier assembly via the CAN communication system.
The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor locks, and turns the magnet clutch off.

DTC Code
DTC Detection Condition
Trouble Area
B1422/22
An open or short in compressor lock sensor circuit.
  1. Cooler compressor assembly (lock sensor)
  2. Compressor drive belt
  3. Harness or connector between cooler compressor assembly (lock sensor) and air conditioning amplifier assembly
  4. Air conditioning amplifier assembly
  5. CAN communication system

WIRING DIAGRAM


E182386E02


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    OK:
    All ECUs and sensors connected to the CAN communication system are displayed.

    Result 
    Result
    Proceed to
    CAN system is normal
    A
    CAN system is abnormal
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
E182660E01
  1. Remove the air conditioning amplifier assembly with the connectors still connected (Click here).

  1. Measure the waveform of the connector.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    H24-8 (LOCK) - H24-13 (SG-2)
    Tool Setting
    200 mV/DIV., 10 ms./DIV.
    Condition
    Engine is running
    Blower switch lo
    A/C switch on
    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC output)
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A


3.INSPECT COOLER COMPRESSOR ASSEMBLY
I104344E04
  1. Check the magnet clutch operation.

    1. Confirm that the magnet clutch hub and magnet clutch rotor lock when the battery positive lead is connected to terminal 3 of the magnet clutch, and the negative lead is connected to the ground wire.
      If the operation is not as specified, replace the magnet clutch assembly.

  1. Measure the resistance between terminals 1 and 2.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SSR+) - 2 (SSR-)
    25°C (77°F)
    165 to 205 Ω



NG
REPLACE COOLER COMPRESSOR ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - COOLER COMPRESSOR)


    E146410E03
  1. Disconnect the H24 amplifier connector.

  1. Disconnect the D39 compressor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H24-8 (LOCK) - D39-1 (SSR+)
    Always
    Below 1 Ω
    H24-13 (SG-2) - D39-2 (SSR-)
    Always
    Below 1 Ω
    H24-8 (LOCK) or D39-1 (SSR+) - Body ground
    Always
    10 kΩ or higher
    H24-13 (SG-2) or D39-2 (SSR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)