Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO RECEIVER

RADIO RECEIVER > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 RADIO BRACKET (for Radio Receiver Type)
  1. Install the No. 2 radio bracket with the 3 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }



2. INSTALL NO. 2 RADIO RECEIVER BRACKET (for Radio and Display Type)
  1. Install the No. 2 radio receiver bracket with the 4 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }



3. INSTALL NO. 1 RADIO BRACKET (for Radio Receiver Type)
  1. Install the No. 1 radio bracket with the 3 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }



4. INSTALL NO. 1 RADIO RECEIVER BRACKET (for Radio and Display Type)
  1. Install the No. 1 radio receiver bracket with the 4 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }



5. INSTALL UPPER INSTRUMENT CLUSTER FINISH PANEL (for Radio and Display Type)
  1. Attach the 2 guides to install the upper instrument cluster finish panel.

  1. Install the 4 screws.



6. INSTALL RADIO RECEIVER ASSEMBLY (for Radio Receiver Type)
  1. Connect the connectors.

  1. Insert the radio receiver assembly and attach the 3 clips on its backside.

    NOTICE:
    When inserting the radio receiver assembly, do not press its knobs.

  1. Install the radio receiver assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



7. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
  1. Connect each connector.

  1. Insert the radio and display receiver assembly and attach the 2 guides and 3 clips on its backside.

    NOTICE:
    When inserting the radio and display receiver assembly, do not press its knobs.

  1. Install the radio and display receiver assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



8. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    I104352
  1. Connect the connectors.

  1. Attach the 4 clips and install the panel.



9. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL
  1. Connect the connectors.

  1. Attach the 4 clips and 2 claws to install the finish panel.



10. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
  1. Attach the 12 clips to install the finish panel.

  1. Connect the 2 connectors and clamp.

  1. Attach the 4 claws to install the instrument panel finish panel retainer.



11. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. Connect the connectors.

  1. Attach the 6 clips to install the console panel.

  1. Install the clip.



12. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. Attach the 12 clips to install the console panel.



13. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    B167312
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



14. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
  1. Attach the 2 claws to install the sensor.

  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 <A> bolts.



15. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
  1. Pass the hood lock control cable assembly into the engine compartment.

  1. Pass the cable rear side through the grommet until the cable stopper is attached to the grommet.

  1. Pass the cable front side through the upper radiator support.



  1. Attach the cable to the clamps as shown in the illustration.


    B220217E01



16. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



17. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



18. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.