Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO RECEIVER

RADIO RECEIVER > REMOVAL

for Preparation Click here



1. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



2. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



3. REMOVE INSTRUMENT SIDE PANEL LH


    B226739
  1. Using a moulding remover, detach the 7 claws and remove the side panel.



4. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


  1. Using a screwdriver with its tip wrapped in protective tape, disconnect the clamps shown in the illustration.


    B220217E01

  1. Pull the cable from the engine room and remove it.



5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


B229064
  1. Remove the 2 <A> bolts.

  1. Detach the 9 clips and claw.



    B163883
  1. Detach the 2 claws and remove the sensor.

  1. Remove the finish panel and then disconnect the connectors.



6. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B161741
  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.



7. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Detach the 12 clips and remove the console panel.



8. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    B222976
  1. Move the shift lever to N.

  1. Remove the clip.

  1. Detach the 6 clips and remove the console panel.

  1. Disconnect the connector.



9. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


B192334
  1. Detach the 4 claws and remove the instrument panel finish panel retainer.



    B219715
  1. Disconnect the 2 connectors and wire harness clamp.

  1. Detach the 12 clips and remove the finish panel.



10. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL


    B223270
  1. Detach the 4 clips and 2 claws.

  1. Disconnect the connectors and remove the finish panel.



11. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    I104352
  1. Detach the 4 clips and separate the panel.

  1. Disconnect the connectors and remove the panel.



12. REMOVE RADIO RECEIVER ASSEMBLY (for Radio Receiver Type)


    B224307
  1. Remove the 4 bolts



    B224308
  1. Pull the radio receiver assembly to detach the 3 clips on the backside of the radio receiver assembly.

  1. Disconnect the connectors and remove the radio receiver assembly.



13. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


    B356854
  1. Remove the 4 bolts.



    B356855
  1. Pull the radio and display receiver assembly to detach the 3 clips and 2 guides on the backside of the radio and display receiver assembly.

  1. Disconnect each connector and remove the radio and display receiver assembly.



14. REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL (for Radio and Display Type)


    B356905
  1. Remove the 4 screws.

  1. Detach the 2 guides and remove the upper instrument cluster finish panel.



15. REMOVE NO. 1 RADIO BRACKET (for Radio Receiver Type)


    B164789
  1. Remove the 3 bolts and No. 1 radio bracket.



16. REMOVE NO. 1 RADIO RECEIVER BRACKET (for Radio and Display Type)


    E299367
  1. Remove the 4 bolts and No. 1 radio receiver bracket.



17. REMOVE NO. 2 RADIO BRACKET (for Radio Receiver Type)


    B164788
  1. Remove the 3 bolts and No. 2 radio bracket.



18. REMOVE NO. 2 RADIO RECEIVER BRACKET (for Radio and Display Type)


    E299366
  1. Remove the 4 bolts and No. 2 radio receiver bracket.