Home › Steering › STEERING COLUMN › STEERING WHEEL

STEERING WHEEL > INSPECTION

for Preparation Click here



1. INSPECT STEERING PAD SWITCH LH


  1. Measure the resistance according to the value(s) in the table below.


    C290061E01


    Text in Illustration 
    *1
    Volume + Switch
    *2
    Volume - Switch
    *3
    Seek + Switch
    *4
    Seek - Switch
    *5
    Mode Switch
    -
    -
    *a
    Component without harness connected
    -
    -

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A10 (AU1) - A8 (EAU)
    No switch is pushed
    95 to 105 kΩ
    Seek+ switch is pushed
    Below 2.5 Ω
    Seek- switch is pushed
    321 to 345 Ω
    Volume+ switch is pushed
    950 to 1050 Ω
    Volume- switch is pushed
    2954 to 3265 Ω
    A9 (AU2) - A8 (EAU)
    No switch is pushed
    95 to 105 kΩ
    Mode switch pushed
    Below 2.5 Ω
    B (HO) - A1 (HO)
    Always
    Below 1 Ω

    If the result is not as specified, replace the steering pad switch assembly.

  1. Check the illumination.

    1. Connect the battery positive (+) lead to terminal A5 (IL+2) and the negative (-) lead to terminal A8 (EAU) of the steering pad switch assembly connector.

    2. Check that the switch illumination comes on.

      OK:
      Steering pad switch illumination comes on.

      If the result is not as specified, replace the steering pad switch assembly.



2. INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Measure the resistance according to the value(s) in the table below.


    C290062E01


    Text in Illustration 
    *1
    Right Switch
    *2
    Up Switch
    *3
    Left Switch
    *4
    Down Switch
    *5
    Enter Switch
    *6
    Back Switch
    *7
    Mode Switch
    *8
    Volume + Switch
    *9
    Volume - Switch
    *10
    Voice Switch
    *11
    Off Hook Switch
    *12
    On Hook Switch
    *a
    Component without harness connected
    -
    -

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A10 (AU1) - A8 (EAU)
    No switch is pushed
    95 to 105 kΩ
    Up switch is pushed
    Below 2.5 Ω
    Down switch is pushed
    313 to 345 Ω
    Volume + switch is pushed
    950 to 1050 Ω
    Volume - switch is pushed
    2955 to 3265 Ω
    A8 (EAU) - A7 (AU3)
    No switch is pushed
    95 to 105 kΩ
    Right switch is pushed
    950 to 1050 Ω
    Left switch is pushed
    2955 to 3265 Ω
    Enter switch is pushed
    Below 2.5 Ω
    Back switch is pushed
    313 to 345 Ω
    A9 (AU2) - A8 (EAU)
    No switch is pushed
    95 to 105 kΩ
    Mode switch is pushed
    Below 2.5 Ω
    Off hook switch is pushed
    950 to 1050 Ω
    On hook switch is pushed
    313 to 345 Ω
    Voice switch is pushed
    2955 to 3265 Ω
    B (HO) - A1 (HO)
    Always
    Below 1 Ω

    If the result is not as specified, replace the steering pad switch assembly.

  1. Check the illumination.

    1. Connect the battery positive (+) lead to terminal A5 (IL+2) and the negative (-) lead to terminal A2 (EAC) of the steering pad switch assembly connector.

    2. Check that the switch illumination comes on.

      OK:
      Steering pad switch illumination comes on.

      If the result is not as specified, replace the steering pad switch assembly.