Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1207/37    Malfunction in Park / Neutral Position Switch

for Preparation Click here


DESCRIPTION

The park/neutral position switch signal is sent to the skid control ECU via the CAN communication system.
When there is a malfunction in the CAN communication system, it will be detected by the diagnostic function.

DTC Code
DTC Detection Condition
Trouble Area
C1207/37
When all conditions below are met:
  1. Yaw rate sensor is normal.
  2. G sensor lateral operation is normal.
  3. Vehicle speed is 40 km/h (24.9 mph) or more.
  4. Reversing signal is output from ECM for 1 second or more.
  1. Park/Neutral position switch
  2. Harness or connector
  3. CAN communication system
  4. VSC actuator (skid control ECU)
  5. ECM

WIRING DIAGRAM


C179938E03


INSPECTION PROCEDURE

NOTICE:
When replacing the VSC actuator assembly, perform zero point calibration (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if the CAN communication system DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY


    C160109E17
  1. Disconnect the D21 switch connector.

  1. Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (RB) - 6 (PL)
    Shift lever in P
    Below 1 Ω
    2 (RB) - 1 (RL)
    Shift lever in R
    2 (RB) - 9 (NL)
    Shift lever in N
    2 (RB) - 7 (DL)
    Shift lever in D
    Shift lever in S, "+" and "-"
    4 (B) - 5 (L)
    Shift lever in P or N
    2 (RB) - 6 (PL)
    Shift lever not in P
    10 kΩ or higher
    2 (RB) - 1 (RL)
    Shift lever not in R
    2 (RB) - 9 (NL)
    Shift lever not in N
    2 (RB) - 7 (DL)
    Shift lever not in D
    Shift lever not in S, "+" and "-"
    4 (B) - 5 (L)
    Shift lever not in P and N



NG
REPLACE PARK / NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


3.CHECK PARK / NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)


    C159064E19
  1. Disconnect the D21 switch connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D21-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V
    D21-2 (RB) - Body ground
    Ignition switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK / NEUTRAL POSITION SWITCH - IGNITION SWITCH)
OK


4.CHECK HARNESS AND CONNECTOR (PARK / NEUTRAL POSITION SWITCH - ECM)


    C179956E01
  1. Disconnect the D21 switch connector.

  1. Disconnect the D56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D21-4 (B) - D56-120 (NSW)
    Always
    Below 1 Ω
    D21-4 (B) or D56-120 (NSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK / NEUTRAL POSITION SWITCH - ECM)
OK


5.CHECK HARNESS AND CONNECTOR (PARK / NEUTRAL POSITION SWITCH - ECM)


    C162013E02
  1. Disconnect the D56 ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D56-2 (P) - Body ground
    Ignition switch ON
    Shift lever in P
    11 to 14 V
    D56-26 (R) - Body ground
    Ignition switch ON
    Shift lever in R
    11 to 14 V*
    D56-25 (N) - Body ground
    Ignition switch ON
    Shift lever in N
    11 to 14 V
    D56-27 (D) - Body ground
    Ignition switch ON
    Shift lever in D
    D56-2 (P) - Body ground
    Ignition switch ON
    Shift lever not in P
    Below 1 V
    D56-26 (R) - Body ground
    Ignition switch ON
    Shift lever not in R
    D56-25 (N) - Body ground
    Ignition switch ON
    Shift lever not in N
    D56-27 (D) - Body ground
    Ignition switch ON
    Shift lever not in D

    HINT:
    *: The voltage will drop slightly due to the turning on of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK / NEUTRAL POSITION SWITCH - ECM)
OK

REPLACE ECM (Click here)