CAMSHAFT > INSPECTION |
| 1. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Install the camshafts (Click here).
Install the camshaft housing (Click here).
Apply a light coat of engine oil on the camshaft and camshaft timing gear.
![]() |
Using the hexagonal portion of the camshaft, align and attach the knock pin of the camshaft with the pin hole of the camshaft timing gear.
![]() |
![]() |
Apply a light coat of engine oil on the threads and under the head of the bolt.
Using a wrench to hold the hexagonal portion of the camshaft, install the camshaft timing gear with the bolt.
Remove the camshaft bearing cap (Click here).
Check the lock of the camshaft timing gear.
Clamp the camshaft in a vise, and confirm that the camshaft timing gear is locked.
![]() |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Break through the tape of the advance side path. Then break through the tape of the retard side path on the opposite side of the advanced side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the two broken paths.
![]() |
Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.
When the camshaft timing gear reaches the most advanced position, release the air pressure from the retard side path and advance side path, in that order.
Check for smooth rotation.
Turn the camshaft timing gear within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.
Check the lock in the most retarded position.
Confirm that the camshaft timing gear is locked at the most retarded position.
Install the camshaft bearing cap (Click here).
Install the camshaft housing (Click here).
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Remove the camshafts (Click here).
![]() |
Remove the flange bolt and camshaft timing gear.
| 2. INSPECT AND ADJUST CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Install the camshafts (Click here).
Install the camshaft housing (Click here).
Apply a light coat of engine oil on the camshaft and camshaft timing exhaust gear.
![]() |
Using the hexagonal portion of the camshaft, align and attach the knock pin of the camshaft with the pin hole of the camshaft timing exhaust gear.
![]() |
Apply a light coat of engine oil on the threads and under the head of the bolt.
![]() |
Using a wrench to hold the hexagonal portion of the camshaft, install the camshaft timing exhaust gear with the bolt.
Remove the camshaft bearing cap (Click here).
Check the camshaft timing exhaust gear lock.
Make sure that the camshaft timing exhaust gear is locked.
![]() |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Break through the tape of the advance side path. Then break through the tape of the retard side path on the opposite side of the advanced side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the two broken paths (the advance side path and the retard side path).
![]() |
Check that the camshaft timing exhaust gear turns in the retard direction when reducing the air pressure applied to the advance side path.
When the camshaft timing exhaust gear moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.
Check for smooth rotation.
Turn the camshaft timing exhaust gear within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear turns smoothly.
Check the lock at the most advanced position.
Make sure that the camshaft timing exhaust gear is locked at the most advanced position.
Install the camshaft bearing cap (Click here).
Install the camshaft housing (Click here).
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Remove the camshafts (Click here).
![]() |
Remove the flange bolt and camshaft timing exhaust gear.