Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. REMOVE ENGINE WIRE


    A259653
  1. Disconnect the 2 camshaft timing control valve connectors.

  1. Disconnect the 4 ignition coil connectors.

  1. Disconnect the 2 VVT sensor connectors.

  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the vacuum switching valve connector (for ACIS).

  1. Disconnect the purge VSV connector.

  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the fuel injector connector.

  1. Remove the bolt and detach the 8 clamps.



    A259650
  1. Disconnect the 2 camshaft timing control valve connectors.

  1. Disconnect the 4 ignition coil connectors.

  1. Disconnect the 2 VVT sensor connectors.

  1. Disconnect the fuel injector connector.

  1. Disconnect the throttle sensor connector.

  1. Disconnect the oil pressure sender gauge connector.

  1. Detach the 9 clamps.



    A259665
  1. Detach the 4 clamps.

  1. Remove the 3 bolts.

  1. Remove the engine wire.



2. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY


    A306994
  1. Remove the No. 1 fuel pipe sub-assembly (Click here).



3. REMOVE CYLINDER BLOCK WATER DRAIN COCK PLUG


    A163838E01
  1. Remove the 2 cylinder block water drain cock plugs from the 2 cylinder block water drains.

  1. Remove the 2 cylinder block water drains from the cylinder block.



4. REMOVE FRONT ENGINE MOUNTING INSULATOR


    A163786
  1. Remove the nut and front engine mounting insulator.



5. REMOVE FRONT ENGINE MOUNTING INSULATOR LH


    A163787
  1. Remove the nut and front engine mounting insulator LH.



6. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    A160649
  1. Remove the 4 bolts and front No. 1 engine mounting bracket RH.



7. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH


    A160648
  1. Remove the 4 bolts and front No. 1 engine mounting bracket LH.



8. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    A162089
  1. Remove the No. 1 engine cover sub-assembly.



9. REMOVE NO. 3 ENGINE COVER


    A162090
  1. Remove the No. 3 engine cover.



10. DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY


    A161418
  1. Disconnect the No. 2 fuel tube from the fuel pressure regulator (for quick type A) (Click here).



11. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A256329
  1. Disconnect the fuel tube from the fuel delivery pipe (for quick type A) (Click here).



    A161415
  1. Disconnect the fuel tube from the No. 2 fuel delivery pipe (for quick type A) (Click here).



12. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A256330
  1. Remove the 2 bolts and fuel delivery pipe.

    NOTICE:
    When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.

  1. Remove the 2 spacers and 4 insulators from the cylinder head RH.



13. REMOVE NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY
  1. Disconnect the No. 7 wire harness connector.



    A256331
  1. Remove the 2 bolts and No. 2 fuel delivery pipe.

    NOTICE:
    When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.

  1. Remove the 2 spacers and 4 insulators from the cylinder head LH.



14. REMOVE VENTILATION HOSE ASSEMBLY


    A163820E02
  1. Remove the 2 bolts and ventilation hose assembly from the intake manifold.



15. REMOVE NO. 1 HOSE TO HOSE TUBE


    A163943
  1. Remove the 2 bolts and No. 1 hose to hose tube.



16. REMOVE INTAKE MANIFOLD


    A307759
  1. Disconnect the throttle body connector from the throttle body assembly.

  1. Slide the 2 clamps and disconnect the 2 water by-pass hoses from the inlet water housing and front water by-pass joint.



    A162103
  1. Slide the clamp and disconnect the ventilation hose from the intake manifold.



    A162082
  1. Disconnect the 2 vacuum switching valve connectors.

  1. Slide the clamp and disconnect the purge line hose from the purge VSV.



    A165518
  1. Remove the 2 bolts.

  1. Slide the clamp and disconnect the union to connector tube hose from the No. 1 tube.



    A165471
  1. Detach the 3 wire harness clamps from the 3 wire harness clamp brackets.



    A165472
  1. Remove the bolt and wire harness clamp bracket from the intake manifold.



    A165478
  1. Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.



17. REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY


    A256359
  1. Remove the 2 bolts and No. 2 fuel tube sub-assembly.



18. REMOVE FUEL TUBE SUB-ASSEMBLY


    A256360
  1. Remove the fuel tube sub-assembly.



19. REMOVE WATER BY-PASS PIPE HOSE
  1. Remove the 3 bolts.



    A165547
  1. Disconnect the 4 hoses and remove the water by-pass pipe.



20. REMOVE NO. 1 WATER BY-PASS HOSE


    A158577E01
  1. Disconnect the No. 1 water by-pass hose from the water by-pass joint and water inlet housing.



21. REMOVE FRONT WATER BY-PASS JOINT


    A291566
  1. Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.

  1. Remove the 4 nuts, front water by-pass joint and 2 gaskets.



22. REMOVE NO. 2 CYLINDER HEAD COVER


A158576
  1. Remove the No. 2 cylinder head cover.



23. REMOVE NO. 1 ENGINE COVER


A158581
  1. Remove the No. 1 engine cover.



24. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY


    A162551
  1. Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the water by-pass pipe sub-assembly.

  1. Remove the 2 bolts and water by-pass pipe sub-assembly.



25. REMOVE WATER PUMP PULLEY


    A151837E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.



26. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A162557
  1. Remove the bolt and No. 1 idler pulley sub-assembly.



27. REMOVE FLUID COUPLING BRACKET


    A162558
  1. Remove the 4 bolts and fluid coupling bracket.



28. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A162527
  1. Remove the standard bolt, 6 mm hexagon wrench bolt and V-ribbed belt tensioner assembly.



29. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY


    A163657
  1. Disconnect the sender gauge connector.



    A162467
  1. Remove the oil pressure sender gauge.



30. REMOVE INLET WATER HOUSING


    A183226
  1. Remove the 3 bolts and inlet water housing and disconnect the No. 3 water by-pass hose from the inlet water housing.

  1. Remove the gasket from the water pump.



31. REMOVE ENGINE WIRE


    A306987
  1. Disconnect the 4 knock sensor connectors.

  1. Detach the 3 clamps, and then remove the engine wire.



32. REMOVE CASE SEPARATOR


    A306989
  1. Slide the 2 clamps, and remove the No. 9 water by-pass hose and No. 10 water by-pass hose from the case separator.



    A306988
  1. Remove the 4 bolts and case separator.



33. REMOVE KNOCK SENSOR


    A158615
  1. Disconnect the 4 knock sensor connectors.

  1. Remove the 4 bolts and 4 knock sensors.



34. REMOVE IGNITION COIL ASSEMBLY


    A151832
  1. Disconnect the 8 ignition coil connectors.

  1. Remove the 8 bolts and 8 ignition coils.