Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE OIL FILTER DRAIN PLUG


    A094910E01
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.



    A207196
  1. Remove the oil filter drain plug.



    A207197
  1. Install the pipe to the oil filter cap.

    HINT:
    Use a container to catch the draining oil.

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.



    A207198
  1. Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.



2. REMOVE OIL FILTER CAP ASSEMBLY


    A207199E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip.



3. REMOVE OIL FILTER ELEMENT


    A209947E01
  1. Remove the oil filter element and O-ring from the oil filter cap.

    NOTICE:
    Be sure to remove the O-ring for the cap by hand, without using any tools, to prevent damage to the cap's O-ring groove.



4. REMOVE NO. 1 OIL COOLER BRACKET


    A163672
  1. Remove the 2 nuts and bracket.

  1. Disconnect the ground wire from the cylinder block.



5. REMOVE OIL FILTER BRACKET


    A162469
  1. Remove the 2 bolts, 2 nuts and filter bracket.



    A162470
  1. Remove the 2 O-rings.



6. REMOVE CRANKSHAFT PULLEY


    A164228E01
  1. Using SST, loosen the crankshaft pulley set bolt.

    SST
    09213-70011  
    09330-00021  

  1. Partially install the pulley set bolt to the crankshaft until 2 or 3 threads are engaged.



    A164229E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



7. REMOVE OIL FILLER CAP SUB-ASSEMBLY


8. REMOVE OIL FILLER CAP HOUSING


    A161903
  1. Remove the 2 bolts, filler cap housing and gasket.



9. REMOVE SPARK PLUG


10. REMOVE VVT SENSOR (for Bank 1)


    A161904
  1. Remove the 2 bolts and 2 VVT sensors.



11. REMOVE VVT SENSOR (for Bank 2)


    A161905
  1. Remove the 2 bolts and 2 VVT sensors.



12. REMOVE CAMSHAFT POSITION SENSOR


    A161906
  1. Remove the bolt and camshaft position sensor.



13. REMOVE CRANK POSITION SENSOR PROTECTOR


A161907
  1. Remove the 2 bolts and sensor protector.



14. REMOVE CRANKSHAFT POSITION SENSOR


    A161908
  1. Remove the bolt and crankshaft position sensor.



15. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH


    A161909
  1. Remove the 2 bolts and 2 oil control valves.



16. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH


    A161910
  1. Remove the 2 bolts and 2 oil control valves.



17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A162523
  1. Remove the 14 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure that the removed parts are returned to the same places they were removed from.



    A162524
  1. Remove the 5 O-rings from the camshaft bearing caps (No. 2, No. 3).



18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A162525
  1. Remove the 14 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure that the removed parts are returned to the same places they were removed from.



    A162526
  1. Remove the 5 O-rings from the camshaft bearing caps (No. 1, No. 3).



19. REMOVE OIL CONTROL VALVE FILTER LH


    A164313E01
  1. Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.



20. REMOVE OIL CONTROL VALVE FILTER RH


    A164314E01
  1. Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.



21. REMOVE SPARK PLUG TUBE GASKET


A164315E01
  1. Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.

  1. Using a screwdriver, pry out the gaskets.

    HINT:
    1. Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.
    2. Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the cylinder head cover.



22. REMOVE WATER PUMP ASSEMBLY


    A151828
  1. Remove the 8 bolts, water pump and gasket.



23. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY


    A162529E01
  1. Remove the 28 bolts and nut shown in the illustration.



    A162530
  1. Remove the timing chain cover by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the cylinder head and cylinder block contact surfaces of the chain cover.



    A162531
  1. Remove the oil pump gasket from the cylinder block.



    A164415
  1. Remove the O-ring from the oil pan.



24. REMOVE INLET WATER PIPE


    A162532
  1. Remove the inlet water pipe.

  1. Remove the 2 O-rings from the inlet water pipe.



25. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL
  1. Place the timing chain cover on wooden blocks.



    A183314E01
  1. Place the oil pump on a wooden block.

  1. Using a screwdriver and wooden block, pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.



26. SET NO. 1 CYLINDER TO TDC / COMPRESSION
  1. Temporarily install the pulley set bolt.



  1. Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.


    A160654E01

    HINT:
    If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



27. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY (for LH Side)


    A174140E01
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.



    A174141E01
  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.



    A160733
  1. Remove the 2 bolts, chain tensioner and gasket.



28. REMOVE CHAIN TENSIONER SLIPPER (for LH Side)


A178535


29. REMOVE NO. 1 CHAIN VIBRATION DAMPER (for LH Side)


    A178536
  1. Remove the 2 bolts and chain vibration damper.



30. REMOVE CHAIN SUB-ASSEMBLY (for LH Side)


    A160655E01
  1. While pushing down the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.



    A160656E01
  1. Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear.



    A160657E01
  1. Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

    NOTICE:
    Be careful not to damage the cylinder head with the wrench.

  1. Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.

  1. Remove the No. 1 and No. 2 chains from the gears.



31. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY


    A148225E01
  1. Remove the 2 bolts and chain tensioner.



32. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY (for RH Side)


    A174142E01
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.



    A174143E01
  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.



    A150146
  1. Remove the 2 bolts and chain tensioner.



33. REMOVE CHAIN TENSIONER SLIPPER (for RH Side)


A178486


34. REMOVE NO. 1 CHAIN VIBRATION DAMPER (for RH Side)


    A160658
  1. Remove the 2 bolts and vibration damper.



35. REMOVE CHAIN SUB-ASSEMBLY (for RH Side)


    A160659E01
  1. While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.



    A160660E01
  1. Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear.



    A160661E01
  1. Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

    NOTICE:
    Be careful not to damage the cylinder head with the wrench.

  1. Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.

  1. Remove the No. 1 and No. 2 chains from the gears.



36. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY


    A148224E01
  1. Remove the 2 bolts and chain tensioner.



37. REMOVE CRANKSHAFT TIMING GEAR KEY


A145630
  1. Using a screwdriver, remove the 2 timing gear keys from the crankshaft.



38. REMOVE CAMSHAFT (for Bank 1)


A163591E01
  1. Make sure that the knock pin of the camshaft is positioned as shown in the illustration.



    A163592E02
  1. Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.



    A163593E02
  1. Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 6 bearing caps.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the No. 3 and No. 4 camshafts.

    HINT:
    Arrange the removed parts in the correct order.



39. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH


    A163594
  1. Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.



40. REMOVE CAMSHAFT (for Bank 2)


A160683E01
  1. Make sure that the knock pin of the camshaft is positioned as shown in the illustration.



    A160684E02
  1. Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.



    A160685E01
  1. Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 6 bearing caps.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the No. 1 and No. 2 camshafts.

    HINT:
    Arrange the removed parts in the correct order.



41. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH


    A160735
  1. Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.



42. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 32 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



43. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 32 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



44. REMOVE VALVE STEM CAP
  1. Remove the 32 valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



45. REMOVE CYLINDER HEAD LH


    A160736E05
  1. Uniformly loosen and remove the 2 bolts in the sequence shown in the illustration.



    A160737E05
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.



46. REMOVE NO. 2 CYLINDER HEAD GASKET


47. REMOVE CYLINDER HEAD SUB-ASSEMBLY


    A160738E04
  1. Uniformly loosen and remove the 2 bolts in the sequence shown in the illustration.



    A160739E03
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.



48. REMOVE CYLINDER HEAD GASKET


49. REMOVE CYLINDER BLOCK WATER JACKET SPACER


A161997
  1. Remove the 2 water jacket spacers from the cylinder head.

    NOTICE:
    Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.



50. REMOVE VENTILATION PIPE GASKET


    A161915E01
  1. Using a screwdriver, pry out the ventilation pipe gasket.

    HINT:
    Tape the screwdriver tip before use.



51. REMOVE NO. 1 HEAT EXCHANGER COVER


    A161916E01
  1. Remove the 12 bolts and 2 nuts.



    A164347
  1. Remove the heat exchanger by prying between the heat exchanger and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.



52. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A160720E01
  1. Remove the 14 bolts and 2 nuts.



    A120816
  1. Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.



53. REMOVE OIL PAN SUB-ASSEMBLY


    A160721E02
  1. Remove the 14 bolts and 2 nuts.

    HINT:
    Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.



    A160722E01
  1. Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.



54. REMOVE NO. 1 OIL PAN BAFFLE PLATE


    A160723
  1. Remove the 7 bolts and baffle plate.



55. REMOVE OIL STRAINER SUB-ASSEMBLY


    A160724
  1. Remove the 2 bolts, oil strainer and O-ring.



56. REMOVE ENGINE REAR OIL SEAL RETAINER


    A145612
  1. Remove the 6 bolts and oil seal retainer.



    A183315E01
  1. Using a screwdriver, pry out the oil seal retainer.

    HINT:
    Tape the screwdriver tip before use.



57. REMOVE OIL DRAIN PIPE SUB-ASSEMBLY


    A160728
  1. Remove the bolt and oil drain pipe.

  1. Remove the O-ring.



58. REMOVE ENGINE REAR OIL SEAL


    A145614E03
  1. Place the oil seal retainer on wooden blocks.

  1. Using a screwdriver and hammer, tap out the oil seal.



59. REMOVE RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.



60. REMOVE STUD BOLT

NOTICE:
If the stud bolt is deformed or its threads are damaged, replace it.