ENGINE OIL COOLER > INSTALLATION |
| 1. INSTALL OIL COOLER SPACER |
![]() |
Apply a light coat of engine oil to a new gasket.
Install the gasket to the oil cooler spacer.
![]() |
Install the oil cooler spacer to the oil filter bracket with the bolt.
| 2. INSTALL OIL COOLER ASSEMBLY |
![]() |
Apply a light coat of engine oil to 2 new O-rings.
Install the 2 O-rings to the oil cooler.
![]() |
Install the oil cooler with the 5 nuts.
| 3. INSTALL OIL FILTER BRACKET |
![]() |
Apply a light coat of engine oil to 2 new O-rings.
Install the 2 O-rings to the timing chain cover.
![]() |
Install the oil filter bracket with the 2 nuts and 2 bolts.
| 4. INSTALL NO. 1 OIL COOLER BRACKET |
![]() |
Connect the ground wire to the cylinder block.
Install the oil cooler bracket with the 2 nuts.
| 5. INSTALL WATER BY-PASS PIPE HOSE |
![]() |
Connect the 4 hoses.
Install the water by-pass pipe with the 3 bolts.
| 6. INSTALL COOLER COMPRESSOR ASSEMBLY |
![]() |
Install the cooler compressor with the 2 stud bolts.
Install the 2 bolts and 2 nuts.
Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor.
| 7. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY |
![]() |
Apply adhesive to 2 or 3 threads of the oil pressure sender gauge.
![]() |
Install the oil pressure sender gauge.
![]() |
Connect the sender gauge connector.
| 8. INSTALL OIL FILTER ELEMENT |
Install the oil filter element (Click here).
| 9. INSTALL FAN & GENERATOR V BELT |
Install the fan and generator V belt (Click here).
| 10. ADD ENGINE OIL |
![]() |
Add fresh oil.
| Oil Grade | Oil Viscosity (SAE) |
| API grade SL or SM multigrade engine oil |
|
| API grade SL "Energy-Conserving", SM "Energy-Conserving" or ILSAC multigrade engine oil |
|
| Item | Specified Condition |
| Drain and refill without oil filter change | 6.6 liters (7.0 US qts., 5.8 Imp. qts.) |
| Drain and refill with oil filter change | 7.0 liters (7.4 US qts., 6.2 Imp. qts.) |
| Dry fill | 8.4 liters (8.9 US qts., 7.4 Imp. qts.) |
| Item | Specified Condition |
| Drain and refill without oil filter change | 7.1 liters (7.4 US qts, 6.2 Imp. qts) |
| Drain and refill with oil filter change | 7.5 liters (7.9 US qts, 6.6 Imp. qts) |
| Dry fill | 9.3 liters (9.8 US qts, 8.2 Imp. qts) |
Install the oil filler cap.
| 11. ADD ENGINE COOLANT |
Add engine coolant.
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 12. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the area that was worked on.
| 13. CHECK ENGINE OIL LEVEL |
Warm up the engine, and then stop the engine and wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the dipstick.
If low, check for leakage and add oil up to the full level mark.
| 14. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.