Home › Engine / Hybrid System › 3UR-FE INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  1. Tighten the radiator drain cock plug by hand.


    A151835E01



2. REMOVE V-BANK COVER SUB-ASSEMBLY


A165576E03
  1. Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.



3. REMOVE AIR CLEANER HOSE ASSEMBLY


A187008
  1. Disconnect the vacuum hose and ventilation hose.

  1. Loosen the 2 clamps.

  1. Remove the air cleaner hose.



4. DISCONNECT VENTILATION HOSE ASSEMBLY


    A162091E01
  1. Disconnect the ventilation hose from the ventilation pipe of the cylinder head cover LH and RH.



5. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


A162089
  1. Remove the No. 1 engine cover sub-assembly.



6. REMOVE NO. 3 ENGINE COVER


A162090
  1. Remove the No. 3 engine cover.



7. REMOVE INTAKE MANIFOLD


    A198620
  1. Disconnect the 2 water by-pass hoses.

  1. Disconnect the throttle W/ motor body connector.



    A162103
  1. Disconnect the ventilation hose.



    A162082
  1. Disconnect the vacuum switching valve connector.

  1. Disconnect the purge line hose from the purge VSV.

  1. Disconnect the vacuum switching valve connector (for ACIS).



    A165518
  1. Remove the 2 bolts.

  1. Disconnect the No. 1 tube from the union to connector tube hose, and move the hose aside.



    A165471
  1. Disconnect the 3 wire clamps from the 3 wire harness clamp brackets.



    A165472
  1. Remove the bolt and wire harness clamp bracket from the intake manifold.



    A165478
  1. Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.



8. REMOVE VENTILATION HOSE ASSEMBLY


    A163820E02
  1. Remove the 2 bolts and ventilation hose from the intake manifold.



9. REMOVE NO. 1 V-BANK COVER BRACKET


    A162104
  1. Remove the 2 bolts and bracket.



10. REMOVE V-BANK COVER BOLT


    A162100E01
  1. Remove the 2 bolts from the intake manifold.



11. REMOVE THROTTLE W/MOTOR BODY ASSEMBLY


    A162080E01
  1. Remove the 4 bolts, throttle W/ motor body and gasket.



12. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A164145
  1. Disconnect the 2 vacuum hoses from the vacuum switching valve.

  1. Remove the bolt and vacuum switching valve.



13. REMOVE PURGE VSV


    A168583
  1. Disconnect the purge line hose from the intake manifold.

  1. Remove the bolt and purge VSV.



14. REMOVE UNION TO CONNECTOR TUBE HOSE


A187011
  1. Remove the tube hose from the intake manifold.



15. REMOVE WIRE HARNESS CLAMP BRACKET


A187010
  1. Remove the 2 bolts and 2 wire harness clamp brackets.