Home › Engine / Hybrid System › 3UR-FE INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. DRAIN ENGINE COOLANT
(Click here)


2. REMOVE V-BANK COVER SUB-ASSEMBLY


    A165576E04
  1. Raise the front of the V-bank cover sub-assembly to detach the 2 pins. Then remove the 2 V-bank cover hooks from the No. 1 V-bank cover bracket, and remove the V-bank cover sub-assembly.
    Text in Illustration 
    *1
    V-bank Cover Grommet
    *2
    Pin
    *3
    No. 1 V-bank Cover Bracket
    *4
    V-bank Cover Hook



3. REMOVE AIR CLEANER HOSE ASSEMBLY


    A187008
  1. Disconnect the vacuum hose from the air cleaner hose assembly.

  1. Slide the clamp and disconnect the ventilation hose from the air cleaner hose assembly.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose assembly.



4. DISCONNECT VENTILATION HOSE ASSEMBLY


    A162091E01
  1. Slide the 2 clamps and disconnect the ventilation hose assembly from the ventilation pipe of the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.



5. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    A162089
  1. Remove the No. 1 engine cover sub-assembly.



6. REMOVE NO. 3 ENGINE COVER


    A162090
  1. Remove the No. 3 engine cover.



7. REMOVE INTAKE MANIFOLD


    A307759
  1. Disconnect the throttle body connector from the throttle body assembly.

  1. Slide the 2 clamps and disconnect the 2 water by-pass hoses from the inlet water housing and front water by-pass joint.



    A162103
  1. Slide the clamp and disconnect the ventilation hose from the intake manifold.



    A162082
  1. Disconnect the 2 vacuum switching valve connectors.

  1. Slide the clamp and disconnect the purge line hose from the purge VSV.



    A165518
  1. Remove the 2 bolts.

  1. Slide the clamp and disconnect the union to connector tube hose from the No. 1 tube.



    A165471
  1. Detach the 3 wire harness clamps from the 3 wire harness clamp brackets.



    A165472
  1. Remove the bolt and wire harness clamp bracket from the intake manifold.



    A165478
  1. Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.



8. REMOVE VENTILATION HOSE ASSEMBLY


    A163820E02
  1. Remove the 2 bolts and ventilation hose assembly from the intake manifold.



9. REMOVE NO. 1 V-BANK COVER BRACKET


    A162104
  1. Remove the 2 bolts and No. 1 V-bank cover bracket.



10. REMOVE V-BANK COVER BOLT


    A162100E01
  1. Remove the 2 V-bank cover bolts from the intake manifold.



11. REMOVE THROTTLE BODY ASSEMBLY


    A198574
  1. Remove the 4 bolts, throttle body assembly and gasket.



12. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A164145
  1. Disconnect the 2 vacuum hoses from the vacuum switching valve assembly.

  1. Remove the bolt and vacuum switching valve assembly.



13. REMOVE PURGE VSV


    A168583
  1. Slide the clamp and disconnect the purge line hose from the intake manifold.

  1. Remove the bolt and purge VSV.



14. REMOVE UNION TO CONNECTOR TUBE HOSE


    A187011
  1. Slide the clamp and remove the union to connector tube hose from the intake manifold.



15. REMOVE WIRE HARNESS CLAMP BRACKET


    A187010
  1. Remove the 2 bolts and 2 wire harness clamp brackets.