Home › Engine / Hybrid System › 3UR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > REMOVAL

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



2. REMOVE FRONT FENDER APRON SEAL RH
  1. Remove the 6 clips and fender apron seal.



3. REMOVE FRONT FENDER APRON SEAL REAR RH
  1. Remove the 5 clips and fender apron seal.



4. REMOVE FRONT FENDER APRON SEAL LH
  1. Remove the 6 clips and fender apron seal.



5. REMOVE FRONT FENDER APRON SEAL REAR LH
  1. Remove the 5 clips and fender apron seal.



6. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the dipstick.

  1. Disconnect the wire harness clamp.



    A164432
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



7. REMOVE CENTER ENGINE UNDER COVER (for 4WD)


    A230307
  1. Remove the 4 bolts and center engine under cover.



8. REMOVE TRANSFER AIR GUIDE (for 4WD)


    A230308
  1. Remove the 2 bolts and transfer air guide.



9. REMOVE PROPELLER SHAFT HEAT INSULATOR (for 4WD)


    C158452
  1. Remove the 2 bolts and heat insulator from the heat insulator bracket.



10. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)


    C179230E03
  1. Place matchmarks on the differential and propeller shaft flange.

  1. Place matchmarks on the transfer and propeller shaft flanges.

  1. Remove the 8 nuts and 8 washers and remove the front propeller shaft assembly.



11. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY


A184981
  1. Remove the 2 bolts from the center exhaust pipe.

  1. Remove the 2 bolts and 2 nuts from the front No. 2 exhaust pipe sub-assembly.

  1. Disconnect the front No. 3 exhaust pipe sub-assembly from the exhaust pipe support.

  1. Remove the 2 gaskets.

  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.



    A184304
  1. Remove the 3 nuts, No. 2 exhaust pipe sub-assembly and gasket.



12. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector and detach the 2 clamps.



    A184982
  1. Remove the 2 bolts from the center exhaust pipe.

  1. Remove the 3 nuts, front exhaust pipe and 2 gaskets.



13. REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR


A184951
  1. Remove the 4 nuts and front No. 4 floor heat insulator.



14. REMOVE FRONT NO. 3 FLOOR HEAT INSULATOR


A184950
  1. Remove the 4 nuts and front No. 3 floor heat insulator.



15. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C155150E01
  1. Put matchmarks on the No. 2 steering intermediate shaft sub-assembly and steering intermediate shaft.

  1. Remove the bolt and disconnect the No. 2 steering intermediate shaft sub-assembly from the steering intermediate shaft.



    C155151E01
  1. Put matchmarks on the No. 2 steering intermediate shaft sub-assembly and the power steering gear.

  1. Remove the bolt and disconnect the No. 2 steering intermediate shaft sub-assembly from the power steering gear.



16. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A162114
  1. Remove the 3 bolts and No. 2 exhaust manifold heat insulator.



17. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


  1. w/ Secondary Air Injection System:



      A162115
    1. Remove the 10 nuts, exhaust manifold sub-assembly LH and 2 gaskets.



  1. w/o Secondary Air Injection System:



      A230303
    1. Remove the 8 nuts, exhaust manifold sub-assembly LH and gasket.



18. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A162752
  1. Remove the 3 bolts and No. 1 exhaust manifold heat insulator.



19. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


  1. w/ Secondary Air Injection System:



      A162754
    1. Remove the 10 nuts, exhaust manifold sub-assembly RH and 2 gaskets.



  1. w/o Secondary Air Injection System:



      A230304
    1. Remove the 8 nuts, exhaust manifold sub-assembly RH and gasket.