Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR DRIVE UNIT

POWER BACK DOOR DRIVE UNIT > INSTALLATION

for Preparation Click here



1. INSTALL POWER BACK DOOR UNIT


    B192141
  1. Install the power back door unit with the 4 bolts.

    Torque:
    14 N*m{ 140 kgf*cm , 10 ft.*lbf }

  1. Connect the connector.



2. INSTALL POWER BACK DOOR ROD


B194234
  1. Install the power back door rod with the 2 stop rings.



3. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH


    B191798
  1. Connect the connector.

  1. Attach the 5 clips to install the rear window No. 2 side garnish assembly LH.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193892
  1. Attach the claw to install the cover.



4. INSTALL QUARTER TRIM PANEL ASSEMBLY LH
  1. Connect the connector.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222458



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



5. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)
  1. Connect the 5 connectors.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Attach the 2 clamps to install the wire harness.



  1. Install the 2 clips.


    B222460



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



6. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Attach the 5 clips and 4 claws to install the rear floor mat support plate.



7. INSTALL ROPE HOOK ASSEMBLY


    B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



8. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



9. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



10. INSTALL REAR FLOOR STEP NO. 1 COVER


    B191404
  1. Attach the 2 claws to install the rear floor step No. 1 cover.



11. INSTALL REAR FLOOR STEP NO. 2 COVER


    B193890
  1. Attach the 2 claws to the install the rear floor step No. 2 cover.



12. INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



13. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Manual Seat)
  1. Install the rear No. 2 seat assembly LH (Click here).



14. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Power Seat)
  1. Install the rear No. 2 seat assembly LH (Click here).



15. INSTALL DECK BOARD BRACKET


    B190119
  1. Install the deck board bracket with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



16. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Install the deck board reinforcement with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



17. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Attach the 5 clips to install the No. 1 deck board.



18. INSTALL ROPE HOOK ASSEMBLY


    B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



19. INSTALL LUGGAGE COMPARTMENT TRIM BOX


    B190116
  1. Install the luggage compartment trim box with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B194633
  1. Install the 4 caps.



20. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B194608
  1. Attach the 4 guides to install the No. 2 deck board.