Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL RECEIVER

DOOR CONTROL RECEIVER > INSTALLATION

for Preparation Click here



1. INSTALL DOOR CONTROL RECEIVER


    B192555
  1. Install the door control receiver with the bolt.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

  1. Connect the connector.



2. INSTALL QUARTER TRIM PANEL ASSEMBLY LH
  1. Connect the connector.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222458



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



3. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)
  1. Connect the 5 connectors.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Attach the 2 clamps to install the wire harness.



  1. Install the 2 clips.


    B222460



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



4. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Attach the 5 clips and 4 claws to install the rear floor mat support plate.



5. INSTALL ROPE HOOK ASSEMBLY


    B190141
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B190139
  1. Attach the 2 claws to install the cover.



6. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



7. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



8. INSTALL REAR FLOOR STEP NO. 1 COVER


    B191404
  1. Attach the 2 claws to install the rear floor step No. 1 cover.



9. INSTALL REAR FLOOR STEP NO. 2 COVER


    B193890
  1. Attach the 2 claws to the install the rear floor step No. 2 cover.



10. INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



11. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Manual Seat Type LH Side)
  1. Install the rear No. 2 seat assembly LH (Click here).



12. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Power Seat Type LH Side)
  1. Install the rear No. 2 seat assembly LH (Click here).



13. INSTALL DECK BOARD BRACKET


    B190119
  1. Install the deck board bracket with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



14. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Install the deck board reinforcement with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



15. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Attach the 5 clips to install the No. 1 deck board.



16. INSTALL ROPE HOOK ASSEMBLY


    B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



17. INSTALL LUGGAGE COMPARTMENT TRIM BOX


    B190116
  1. Install the luggage compartment trim box with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B194633
  1. Install the 4 caps.



18. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B194608
  1. Attach the 4 guides to install the No. 2 deck board.