Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > INSTALLATION

for Preparation Click here



1. INSTALL FRONT BUMPER COVER


    B220209
  1. Attach the 4 claws to install the front bumper cover.

  1. Connect the connectors.

    HINT:
    If vehicle equipped with fog lights or ultrasonic sensors, connect the connectors.



    B220208E01
  1. Install the 8 clips.

  1. Install the 7 screws.

    Torque:
    for labeled A:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



    B195311E01
  1. Install the 2 pin hold clips.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Install the clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Install the screw.

    HINT:
    Use the same procedure for the RH side and LH side.



2. INSTALL FRONT END PANEL LH (w/o Headlight Cleaner System)


    B191651
  1. Attach the 2 clips to install the front end panel.



    B191650
  1. Install the 2 clips.



3. INSTALL FRONT END PANEL RH (w/o Headlight Cleaner System)

HINT:
Use the same procedure as for the LH side.



4. INSTALL FRONT END PANEL LH (w/ Headlight Cleaner System)


    B191652
  1. Attach the 2 claws and 2 clips to install the front end panel.



    B191650
  1. Install the 2 clips.



5. INSTALL FRONT END PANEL RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure as for the LH side.



6. PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT
  1. Prepare the vehicle:

    1. Make sure that there is no damage to the body around the headlights.
    2. Fill the fuel tank.
    3. Make sure that the oil is filled to the specified level.
    4. Make sure that the coolant is filled to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.
    7. Have a person of average weight (75 kg, 165 lb) sit in the driver seat.
    8. w/ Suspension Control System:
      Vehicles with height adjustable suspension should have the vehicle height set to the lowest setting prior to adjusting the headlight aim.



7. PREPARE FOR HEADLIGHT AIMING (for Using a Tester)
  1. Prepare the vehicle for headlight aim check.

  1. Adjust in accordance with the headlight tester instructions.



8. PREPARE FOR HEADLIGHT AIMING (for Using a Screen)


E163384E03
  1. Prepare the vehicle.
    Text in Illustration 
    *a
    90 °
    *b
    25 m or 3 m

    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Create a 25 m (82 ft.) distance between the vehicle (headlight bulb center) and the wall.
    4. Make sure that the vehicle is on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

      NOTICE:
      A distance of 25 m (82 ft.) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).

  1. Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.

  1. Draw a vertical line down the center of the screen (V line).

  1. Set the screen as shown in the illustration.

    HINT:
    1. Stand the screen perpendicular to the ground.

    2. Align the V line on the screen with the center of the vehicle.


      E163383E04



    E257183E01
  1. Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
    Text in Illustration 
    *a
    V LH Line
    *b
    V Line
    *c
    V RH Line
    *d
    H Line
    *e
    Ground

    HINT:
    1. The base lines differ for "low beam inspection" and "high beam inspection".
    2. Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the name of the manufacturer marked on the headlight as the center mark.


    1. H Line (Headlight height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.

    2. V LH Line and V RH Line (Center mark positions of left-hand (LH) and right-hand (RH) headlights):
      Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).



9. INSPECT HEADLIGHT AIMING
  1. Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming.

    NOTICE:
    Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

    HINT:
    When checking the aim of the high beam headlight, cover the low beam headlight or disconnect the connector.

  1. Start the engine.

  1. Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

    HINT:
    1. Since the low beam and high beam headlight on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
    2. If the alignment distance is 25 m (82 ft.):
      The low beam cutoff line should be within 48 mm (1.88 in.) and 698 mm (2.28 ft.) below the H line as well as 249 mm (9.80 in.) left or right of the V LH or V RH line.
    3. If the alignment distance is 3 m (9.84 ft.):
      The low beam cutoff line should be within 6 mm (0.23 in.) and 84 mm (3.30 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.
    4. If the alignment distance is 25 m (82 ft.):
      The horizontal line of the preferred low beam cutoff line is 249 mm (9.80 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

    5. If the alignment distance is 3 m (9.84 ft.):
      The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.


      E262297E01

  1. Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration.

    HINT:
    1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
    2. If the alignment distance is 25 m (82.0 ft.):
      The high beam center of intensity should be within 175 mm (6.88 in.) above and 249 mm (9.80 in.) below the H line as well as 497 mm (1.63 ft.) left or right of the V LH or V RH line.

    3. If the alignment distance is 3 m (9.84 ft.):
      The high beam center of intensity should be within 21 mm (0.82 in.) above and 30 mm (1.18 in.) below the H line as well as 60 mm (2.36 in.) left or right of the V LH or V RH line.


      E261529E01



10. ADJUST HEADLIGHT AIMING


E163385E03
  1. Using a screwdriver, adjust the aim.
    Adjust the aim of each headlight to the specified range by turning each aiming screw with a screwdriver.
    Text in Illustration 
    *1
    Vertical Aiming Screw
    *2
    Horizontal Aiming Screw

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

    HINT:
    1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
    2. When adjusting the horizontal axis of the headlight, the vertical axis will also change. It is necessary to adjust the horizontal position first, and then correct the vertical position.
    3. If it is not possible to correctly adjust headlight aim, check the bulb, headlight unit and headlight unit reflector installation.
    4. The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves right when turning the horizontal aiming screw clockwise, and moves left when turning the horizontal aiming screw counterclockwise.
    5. Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.



11. PREPARE VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT
  1. Prepare the vehicle:

    1. Make sure that there is no damage to or deformation of the body around the fog lights.
    2. Fill the fuel tank.
    3. Make sure that the oil is filled to the specified level.
    4. Make sure that the coolant is filled to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.
    7. Have a person of average weight (75 kg, 165 lb) sit in the driver's seat.
    8. w/ Suspension Control System:
      Vehicles with height adjustable suspension should have the vehicle height set to the lowest setting prior to adjusting the headlight aim.



12. PREPARE FOR FOG LIGHT AIMING


E143852E05
  1. Prepare the vehicle.
    Text in Illustration 
    *a
    90 °
    *b
    25 m or 3 m

    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Create a 25 m (82 ft.) distance between the vehicle (fog light bulb center) and the wall.
    4. Make sure that the vehicle is on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

      NOTICE:
      A distance of 25 m (82 ft.) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).

  1. Prepare a piece of thick white paper approximately 2.0 m (6.56 ft.) (height) x 4.0 m (13.1 ft.) (width) to use as a screen.

  1. Draw a vertical line down the center of the screen (V line).

  1. Set the screen as shown in the illustration.

    HINT:
    1. Stand the screen perpendicular to the ground.

    2. Align the V line on the screen with the center of the vehicle.


      E143853E04



    E257183E01
  1. Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.
    Text in Illustration 
    *a
    V LH Line
    *b
    V Line
    *c
    V RH Line
    *d
    H Line
    *e
    Ground

    HINT:
    Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


    1. H Line (Fog light height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.

    2. V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
      Draw 2 vertical lines so that they intersect the H line at each center mark.



13. INSPECT FOG LIGHT AIMING
  1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

    NOTICE:
    Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

  1. Start the engine.



  1. Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration.

    HINT:
    1. If the alignment distance is 25 m (82 ft.):
      The upper edge of the hot zone for the fog light should be 436 mm (17.2 in.) below the H line.
    2. If the alignment distance is 3 m (9.84 ft.):
      The upper edge of the hot zone for the fog light should be 52 mm (2.05 in.) below the H line.



    B117629E40



14. ADJUST FOG LIGHT AIMING


E183089E02
  1. Adjust the aim vertically:
    Text in Illustration 
    *1
    Aiming Screw
    Adjust the aim of each fog light to the specified range by turning the aiming screw with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

    HINT:
    If it is not possible to correctly adjust fog light aim, check the bulb, fog light unit, and fog light unit reflector installation.