Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT BUMPER GARNISH


    B194120
  1. Remove the 6 clips.

  1. Detach the 5 claws and remove the front bumper garnish.



2. REMOVE FOG LIGHT COVER LH


    B194122
  1. Detach the 6 claws and remove the fog light cover.



3. REMOVE FOG LIGHT COVER RH

HINT:
Use the same procedure as for the LH side.



4. REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)


    E161819
  1. Detach the 2 claws and remove the fog light.



5. REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



6. REMOVE NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to remove the No. 1 ultrasonic sensor on the other side.

  1. Disconnect the connector.



    E134853
  1. While pushing down on the lever with a finger to release the claw, disengage the claw on the other side to remove the ultrasonic sensor.

    HINT:
    The type of the claws on the top and bottom of the sensor are different. Observe the claws carefully before attempting to removing the sensor.



7. REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to remove the No. 1 ultrasonic sensor retainer on the other side.



    E146464
  1. Detach the 2 claws and remove the ultrasonic sensor retainer from the front bumper.



8. REMOVE FRONT FENDER LINER BRACKET LH


    B194119
  1. Detach the 2 claws and remove the front fender liner bracket.



9. REMOVE FRONT FENDER LINER BRACKET RH

HINT:
Use the same procedure as for the LH side.



10. REMOVE CLIP


    B194123
  1. Remove the clip.

    HINT:
    Use the same procedure for the remaining parts.



11. REMOVE FRONT BUMPER SIDE SUPPORT LH


    B194115
  1. Remove the 2 screws.

  1. Detach the 3 claws and remove the front bumper side support.



12. REMOVE FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure as for the LH side.



13. REMOVE FRONT UPPER CENTER BUMPER RETAINER


    B220211
  1. Remove the 6 nuts and front upper center bumper retainer.



14. REMOVE FRONT BUMPER END RETAINER LH


    B194117
  1. Remove the 3 nuts and front bumper end retainer.



15. REMOVE FRONT BUMPER END RETAINER RH

HINT:
Use the same procedure as for the LH side.



16. REMOVE FRONT BUMPER REINFORCEMENT


    B220212
  1. Remove the 6 nuts and the front bumper reinforcement.

  1. Disconnect the connectors.

    HINT:
    If vehicle equipped with laser radar sensors, disconnect the connectors.



17. REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH


    B194124
  1. Remove the 4 nuts and the front No. 2 bumper extension.

    HINT:
    The front No. 2 bumper extension cannot be removed easily if the stud bolts on the back side are caught in the body.



18. REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



19. REMOVE RADIATOR SIDE DEFLECTOR LH


    B194125
  1. Using a clip remover, remove the 6 clips and radiator side deflector.



20. REMOVE RADIATOR SUPPORT TO FRAME SEAL RH


    B219918
  1. Using a clip remover, remove the 2 clips and radiator support to frame seal.