Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > DISASSEMBLY

for Preparation Click here



1. REMOVE NO. 2 ULTRASONIC SENSOR


  1. Detach the 4 claws and remove the No. 2 ultrasonic sensor as shown in the illustration.

    HINT:
    The illustration shows the No. 2 ultrasonic sensor for the RH. The horizontal orientation of the No. 2 ultrasonic sensor for the LH is opposite that of the image shown in the illustration.



    B354819



2. REMOVE FRONT BUMPER GARNISH


    B384488
  1. Remove the 6 clips.

  1. Detach the 17 claws and remove the front bumper garnish.



3. REMOVE FRONT BUMPER MOULDING RETAINER


    B384489
  1. Remove the 5 screws.

  1. Detach the 6 guides and remove the front bumper moulding retainer.



4. REMOVE FOG LIGHT COVER LH
  1. Remove the clip.



    B380283
  1. Detach the 5 claws and remove the fog light cover LH.



5. REMOVE FOG LIGHT COVER RH

HINT:
Use the same procedure as for the LH side.



6. REMOVE FOG LIGHT MOUNTING BRACKET LH (w/ Fog Light)


    E161818
  1. Remove the 3 bolts and the fog light mounting bracket.



7. REMOVE FOG LIGHT MOUNTING BRACKET RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



8. REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)


    E161819
  1. Detach the 2 claws and remove the fog light.



9. REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



10. REMOVE FRONT FENDER LINER BRACKET LH


    B194119
  1. Detach the 2 claws and remove the front fender liner bracket LH.



11. REMOVE FRONT FENDER LINER BRACKET RH

HINT:
Use the same procedure as for the LH side.



12. REMOVE CLIP


    B194123
  1. Remove the clip.

    HINT:
    Use the same procedure for the remaining parts.



13. REMOVE FRONT BUMPER SIDE SUPPORT LH


    B194115
  1. Remove the 2 screws.

  1. Detach the 3 claws and remove the front bumper side support LH.



14. REMOVE FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure as for the LH side.



15. REMOVE FRONT UPPER CENTER BUMPER RETAINER


    B220211
  1. Remove the 6 nuts and front upper center bumper retainer.



16. REMOVE FRONT BUMPER END RETAINER LH


    B194117
  1. Remove the 3 nuts and front bumper end retainer LH.



17. REMOVE FRONT BUMPER END RETAINER RH

HINT:
Use the same procedure as for the LH side.



18. REMOVE FRONT BUMPER REINFORCEMENT


    B220212
  1. Remove the 6 nuts and the front bumper reinforcement.



19. REMOVE FRONT BUMPER SIDE BRACKET

HINT:
Use the same procedure for both front bumper side brackets.

  1. Put a 7 mm (0.276 in.) drill bit into a drill.

  1. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

    HINT:
    Tape the 7 mm (0.276 in.) drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill against the 3 rivets and drill off the flanges of the 3 rivets.

    CAUTION:
    Be careful of the drilled rivet as it may become hot.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.

  1. Remove the front bumper side bracket.



  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


    B380284E01


    Standard:

    Area
    Specified Condition
    A
    5 mm (0.197 in.)



20. REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH


    B194124
  1. Remove the 4 nuts and the front No. 2 bumper extension sub-assembly LH.

    HINT:
    The front No. 2 bumper extension cannot be removed easily if the stud bolts on the back side are caught in the body.



21. REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



22. REMOVE RADIATOR SIDE DEFLECTOR LH


    B194125
  1. Using a clip remover, remove the 6 clips and radiator side deflector LH.



23. REMOVE RADIATOR SUPPORT TO FRAME SEAL RH


    B219918
  1. Using a clip remover, remove the 2 clips and radiator support to frame seal RH.