Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL RADIATOR SIDE DEFLECTOR LH


    B194125
  1. Install the radiator side deflector with the 6 clips.



2. INSTALL RADIATOR SUPPORT TO FRAME SEAL RH


    B219918
  1. Install the radiator support to frame seal with the 2 clips.



3. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH


    B194124
  1. Install the front No. 2 bumper extension with the 4 nuts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }



4. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



5. INSTALL FRONT BUMPER REINFORCEMENT


    B220212
  1. Install the front bumper reinforcement with the 6 nuts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }

  1. Connect the connectors.

    HINT:
    If vehicle equipped with laser radar sensors, connect the connectors.



6. INSTALL FRONT BUMPER END RETAINER LH


    B194117
  1. Install the front bumper end retainer with the 3 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



7. INSTALL FRONT BUMPER END RETAINER RH

HINT:
Use the same procedure as for the LH side.



8. INSTALL FRONT UPPER CENTER BUMPER RETAINER


    B220211
  1. Install the front upper center bumper retainer with the 6 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



9. INSTALL FRONT BUMPER SIDE SUPPORT LH


    B194115
  1. Attach the 3 claws to install the front bumper side support.

  1. Install the 2 screws.



10. INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure as for the LH side.



11. INSTALL CLIP


    B194123
  1. Install the clip.

    HINT:
    Use the same procedure for the remaining parts.



12. INSTALL FRONT FENDER LINER BRACKET LH


    B194119
  1. Attach the 2 claws to install the front fender liner bracket.



13. INSTALL FRONT FENDER LINER BRACKET RH

HINT:
Use the same procedure as for the LH side.



14. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor retainer on the other side.



    E146465E01
  1. Install the ultrasonic sensor retainer to the front bumper.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.



15. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor on the other side.



    E146466
  1. Attach the 2 claws to install the ultrasonic sensor.

  1. Connect the connector.



16. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)


    E161819
  1. Attach the 2 claws to install the fog light.



17. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



18. INSTALL FOG LIGHT COVER LH


    B194122
  1. Attach the 6 claws to install the fog light cover.



19. INSTALL FOG LIGHT COVER RH

HINT:
Use the same procedure as for the LH side.



20. INSTALL FRONT BUMPER GARNISH


    B194120
  1. Attach the 5 claws to install the front bumper garnish.

  1. Install the 6 clips.