Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL RADIATOR SIDE DEFLECTOR LH


    B194125
  1. Install the radiator side deflector LH with the 6 clips.



2. INSTALL RADIATOR SUPPORT TO FRAME SEAL RH


    B219918
  1. Install the radiator support to frame seal RH with the 2 clips.



3. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH


    B194124
  1. Install the front No. 2 bumper extension sub-assembly LH with the 4 nuts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }



4. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



5. INSTALL FRONT BUMPER SIDE BRACKET

HINT:
Use the same procedure for both front bumper side brackets.

  1. Install the front bumper side bracket.

  1. Install a nose piece to an air riveter or hand riveter.

  1. Insert the mandrel part of a new rivet into the nose piece.



  1. Place the riveter upright against the front bumper side bracket and install the 3 rivets.

    HINT:
    If the rivet cannot be cut, pull it once and cut it.

    NOTICE:

    1. B171664E15
      Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.
      Text in Illustration 
      *1
      Riveter
      *2
      Mandrel
      *a
      INCORRECT
      *b
      CORRECT

    2. B172390E17
      Confirm that the rivets are seated properly against the front bumper side bracket.
    3. Do not tilt the riveter when installing the rivet to the front bumper side bracket.
    4. Do not leave any space between the rivet head and front bumper side bracket.
      Text in Illustration 
      *1
      Riveter
      *a
      INCORRECT
      *b
      CORRECT

    5. B172391E15
      Do not leave any space between the front bumper side bracket and front door panel. Firmly hold together the 2 items while installing the rivet.
      Text in Illustration 
      *1
      Riveter
      *a
      INCORRECT
      *b
      CORRECT



    B380285



6. INSTALL FRONT BUMPER REINFORCEMENT


    B220212
  1. Install the front bumper reinforcement with the 6 nuts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }



7. INSTALL FRONT BUMPER END RETAINER LH


    B194117
  1. Install the front bumper end retainer LH with the 3 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



8. INSTALL FRONT BUMPER END RETAINER RH

HINT:
Use the same procedure as for the LH side.



9. INSTALL FRONT UPPER CENTER BUMPER RETAINER


    B220211
  1. Install the front upper center bumper retainer with the 6 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



10. INSTALL FRONT BUMPER SIDE SUPPORT LH


    B194115
  1. Attach the 3 claws to install the front bumper side support LH.

  1. Install the 2 screws.



11. INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure as for the LH side.



12. INSTALL CLIP


    B194123
  1. Install the clip.

    HINT:
    Use the same procedure for the remaining parts.



13. INSTALL FRONT FENDER LINER BRACKET LH


    B194119
  1. Attach the 2 claws to install the front fender liner bracket LH.



14. INSTALL FRONT FENDER LINER BRACKET RH

HINT:
Use the same procedure as for the LH side.



15. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)


    E161819
  1. Attach the 2 claws to install the fog light.



16. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



17. INSTALL FOG LIGHT MOUNTING BRACKET LH (w/ Fog Light)


    E161818
  1. Install the fog light mounting bracket with the 3 bolts.



18. INSTALL FOG LIGHT MOUNTING BRACKET RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



19. INSTALL FOG LIGHT COVER LH


    B380283
  1. Attach the 5 claws to install the fog light cover LH.

  1. Install the clip.



20. INSTALL FOG LIGHT COVER RH

HINT:
Use the same procedure as for the LH side.



21. INSTALL FRONT BUMPER GARNISH


    B384488
  1. Attach the 17 claws to install the front bumper garnish.

  1. Install the 6 clips.



22. INSTALL NO. 2 ULTRASONIC SENSOR


  1. Attach the 4 claws to install the No. 2 ultrasonic sensor as shown in the illustration.

    HINT:
    1. No. 2 ultrasonic sensor direction is the same as the keyhole direction.
    2. Do not damage the bumper with the protrusion when installing the No. 2 ultrasonic sensor.



    B354822E03


    Text in Illustration 
    *a
    No. 2 ultrasonic sensor direction
    *b
    Keyhole direction