AIR CONDITIONING SYSTEM > Cooling Box Circuit |


| 1.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Body / Air Conditioner / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| COOL-BOX Evaporator Temp | Cooler thermistor (cooling box) / Min.: 0°C (32°F) Max.: 59.55°C (139.19°F) | Actual cooling box temperature is displayed | Open in the circuit: 0°C (32°F) Short in the circuit: 59.55°C (139.19°F) |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.INSPECT COOLER THERMISTOR |
![]() |
Remove the cooler thermistor .
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | -10°C (14°F) | 7.30 to 9.10 kΩ |
| -5°C (23°F) | 5.65 to 6.95 kΩ | |
| 0°C (32°F) | 4.40 to 5.35 kΩ | |
| 5°C (41°F) | 3.40 to 4.15 kΩ | |
| 10°C (50°F) | 2.70 to 3.25 kΩ | |
| 15°C (59°F) | 2.14 to 2.58 kΩ | |
| 20°C (68°F) | 1.71 to 2.05 kΩ | |
| 25°C (77°F) | 1.38 to 1.64 kΩ | |
| 30°C (86°F) | 1.11 to 1.32 kΩ |
| *a | Sensor |
| *b | Resistance (kΩ) |
| *c | Temperature (°C (°F)) |
|
| ||||
| OK | |
| 3.INSPECT NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY |
![]() |
Remove the No. 1 cooler wiring harness sub-assembly .
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-1 (+) - E-2 | Always | Below 1 Ω |
| A-6 (-) - E-1 | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Vehicle Harness) |
| *b | Front view of wire harness connector (to Cooler Thermistor) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (COOLING BOX - AIR CONDITIONING AMPLIFIER) |
Disconnect the S9 cooling box assembly connector.
Disconnect the H24 and H67 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S9-1 (+) - H67-16 (TECB) | Always | Below 1 Ω |
| S9-6 (-) - H24-35 (SG-4) | Always | Below 1 Ω |
| S9-1 (+) - Body ground | Always | 10 kΩ or higher |
| S9-6 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (COOLING BOX - BATTERY AND BODY GROUND) |
![]() |
Disconnect the S9 cooling box assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S9-10 (+B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S9-3 (L) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Cooling Box Assembly) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (COOLING BOX - IG1 NO. 3 RELAY) |
![]() |
Disconnect the S9 cooling box assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S9-5 (B) - Body ground | Ignition switch off | Below 1 V |
| S9-5 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Cooling Box Assembly) |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH - IG1 NO. 3 RELAY AND TAIL RELAY) |
![]() |
Disconnect the H113 cooler control switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H113-2 (IND) - Body ground | Ignition switch off | Below 1 V |
| H113-2 (IND) - Body ground | Ignition switch ON | 11 to 14 V |
| H113-5 (ILL+) - Body ground | Headlight dimmer switch off | Below 1 V |
| H113-5 (ILL+) - Body ground | Headlight dimmer switch on | 11 to 14 V |
| *a | Front view of wire harness connector (to Cooler Control Switch Assembly) |
|
| ||||
| OK | |
| 8.INSPECT COOLER CONTROL SWITCH ASSEMBLY |
![]() |
Remove the cooler control switch assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3 (-S) - 6 (+S) | Cooler control switch assembly on | Below 1 Ω |
| 3 (-S) - 6 (+S) | Cooler control switch assembly off | 10 kΩ or higher |
Apply battery voltage to the cooler control switch assembly connector and check that the cooler control switch assembly illuminates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 2 (IND) Battery negative (-) → Terminal 7 (IND-) | LED illuminates |
| Battery positive (+) → Terminal 5 (ILL+) Battery negative (-) → Terminal 4 (ILL-) | LED illuminates |
| *a | Component without harness connected (Cooler Control Switch Assembly) |
|
| ||||
| OK | |
| 9.INSPECT COOLER BLOWER MOTOR |
![]() |
Remove the cooler blower motor .
Apply battery voltage to the cooler blower motor and check that the cooler blower motor operates smoothly.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 2 | Motor operates smoothly |
| *a | Component without harness connected (Cooler Blower Motor) |
|
| ||||
| OK | |
| 10.INSPECT NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY |
![]() |
Remove the No. 1 cooler wiring harness sub-assembly .
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-2 (+S) - B-5 (SW) | Always | Below 1 Ω |
| A-3 (L) - B-4 (GND) | Always | Below 1 Ω |
| A-4 (ACT) - B-6 (CBI) | Always | Below 1 Ω |
| A-5 (B) - B-2 (IG) | Always | Below 1 Ω |
| A-5 (B) - C-2 | Always | Below 1 Ω |
| A-5 (B) - D-1 | Always | Below 1 Ω |
| A-7 (ICEI) - B-10 (SG) | Always | Below 1 Ω |
| A-9 (COLI) - B-8 (CBT) | Always | Below 1 Ω |
| A-10 (+B) - B-1 (+B) | Always | Below 1 Ω |
| B-9 (BLW) - C-1 | Always | Below 1 Ω |
| B-9 (BLW) - D-2 | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Vehicle Harness) |
| *b | Front view of wire harness connector (to Cool Box Air Conditioning Amplifier Assembly) |
| *c | Front view of wire harness connector (to Cooler Magnet Valve Assembly) |
| *d | Front view of wire harness connector (to Cooler Blower Motor) |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (COOLING BOX - AIR CONDITIONING AMPLIFIER) |
Disconnect the S9 cooling box assembly connector.
Disconnect the H24 and H67 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S9-4 (ACT) - H67-12 (SWCB) | Always | Below 1 Ω |
| S9-9 (COLI) - H24-26 (COOL) | Always | Below 1 Ω |
| S9-4 (ACT) - Body ground | Always | 10 kΩ or higher |
| S9-9 (COLI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH - AIR CONDITIONING AMPLIFIER) |
Disconnect the H113 cooler control switch assembly connector.
Disconnect the H67 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H113-7 (IND-) - H67-11 (LED) | Always | Below 1 Ω |
| H113-7 (IND-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH - COOLING BOX) |
Disconnect the H113 cooler control switch assembly connector.
Disconnect the S9 air cooling box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H113-3 (-S) - S9-7 (ICEI) | Always | Below 1 Ω |
| H113-6 (+S) - S9-2 (+S) | Always | Below 1 Ω |
| H113-3 (-S) - Body ground | Always | 10 kΩ or higher |
| H113-6 (+S) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 14.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH - COMBINATION METER) |
Disconnect the H113 cooler control switch assembly connector.
Disconnect the H37 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H113-4 (ILL-) - H37-37 (ILL-) | Always | Below 1 Ω |
| H113-4 (ILL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||