Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > Cooling Box Circuit

for Preparation Click here


DESCRIPTION

When the cooler control switch assembly is pushed, the cooler blower motor and cooler magnet valve assembly controlled by the air conditioning amplifier assembly and cool box air conditioning amplifier assembly operate. If the cooling box assembly does not operate when the cooler control switch assembly is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM


E208795E01


E208796E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. According to the display on the tester, read the Data List.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    COOL-BOX Evaporator Temp
    Cooler thermistor (cooling box) /
    Min.: 0°C (32°F)
    Max.: 59.55°C (139.19°F)
    Actual cooling box temperature is displayed
    Open in the circuit: 0°C (32°F)
    Short in the circuit: 59.55°C (139.19°F)

    OK:
    The display is as specified in the normal condition.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 5
A


2.INSPECT COOLER THERMISTOR


    E161018E03
  1. Remove the cooler thermistor .

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    -10°C (14°F)
    7.30 to 9.10 kΩ
    -5°C (23°F)
    5.65 to 6.95 kΩ
    0°C (32°F)
    4.40 to 5.35 kΩ
    5°C (41°F)
    3.40 to 4.15 kΩ
    10°C (50°F)
    2.70 to 3.25 kΩ
    15°C (59°F)
    2.14 to 2.58 kΩ
    20°C (68°F)
    1.71 to 2.05 kΩ
    25°C (77°F)
    1.38 to 1.64 kΩ
    30°C (86°F)
    1.11 to 1.32 kΩ

    Text in Illustration 
    *a
    Sensor
    *b
    Resistance (kΩ)
    *c
    Temperature (°C (°F))

    NOTICE:
    1. Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.
    2. When measuring, the sensor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (see the graph).



NG
REPLACE COOLER THERMISTOR
OK


3.INSPECT NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY


    E214743E01
  1. Remove the No. 1 cooler wiring harness sub-assembly .

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-1 (+) - E-2
    Always
    Below 1 Ω
    A-6 (-) - E-1
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Vehicle Harness)
    *b
    Front view of wire harness connector
    (to Cooler Thermistor)



NG
REPLACE NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (COOLING BOX - AIR CONDITIONING AMPLIFIER)
  1. Disconnect the S9 cooling box assembly connector.

  1. Disconnect the H24 and H67 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S9-1 (+) - H67-16 (TECB)
    Always
    Below 1 Ω
    S9-6 (-) - H24-35 (SG-4)
    Always
    Below 1 Ω
    S9-1 (+) - Body ground
    Always
    10 kΩ or higher
    S9-6 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (COOLING BOX - BATTERY AND BODY GROUND)


    E208797E01
  1. Disconnect the S9 cooling box assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S9-10 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S9-3 (L) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Cooling Box Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (COOLING BOX - IG1 NO. 3 RELAY)


    E208797E02
  1. Disconnect the S9 cooling box assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S9-5 (B) - Body ground
    Ignition switch off
    Below 1 V
    S9-5 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Cooling Box Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH - IG1 NO. 3 RELAY AND TAIL RELAY)


    E208798E01
  1. Disconnect the H113 cooler control switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H113-2 (IND) - Body ground
    Ignition switch off
    Below 1 V
    H113-2 (IND) - Body ground
    Ignition switch ON
    11 to 14 V
    H113-5 (ILL+) - Body ground
    Headlight dimmer switch off
    Below 1 V
    H113-5 (ILL+) - Body ground
    Headlight dimmer switch on
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Cooler Control Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT COOLER CONTROL SWITCH ASSEMBLY


    I105746E01
  1. Remove the cooler control switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (-S) - 6 (+S)
    Cooler control switch assembly on
    Below 1 Ω
    3 (-S) - 6 (+S)
    Cooler control switch assembly off
    10 kΩ or higher

  1. Apply battery voltage to the cooler control switch assembly connector and check that the cooler control switch assembly illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 2 (IND)
    Battery negative (-) → Terminal 7 (IND-)
    LED illuminates
    Battery positive (+) → Terminal 5 (ILL+)
    Battery negative (-) → Terminal 4 (ILL-)
    LED illuminates

    Text in Illustration 
    *a
    Component without harness connected
    (Cooler Control Switch Assembly)



NG
REPLACE COOLER CONTROL SWITCH ASSEMBLY (Click here)
OK


9.INSPECT COOLER BLOWER MOTOR


    B188371E02
  1. Remove the cooler blower motor .

  1. Apply battery voltage to the cooler blower motor and check that the cooler blower motor operates smoothly.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 2
    Motor operates smoothly

    Text in Illustration 
    *a
    Component without harness connected
    (Cooler Blower Motor)



NG
REPLACE COOLER BLOWER MOTOR
OK


10.INSPECT NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY


    E214742E01
  1. Remove the No. 1 cooler wiring harness sub-assembly .

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (+S) - B-5 (SW)
    Always
    Below 1 Ω
    A-3 (L) - B-4 (GND)
    Always
    Below 1 Ω
    A-4 (ACT) - B-6 (CBI)
    Always
    Below 1 Ω
    A-5 (B) - B-2 (IG)
    Always
    Below 1 Ω
    A-5 (B) - C-2
    Always
    Below 1 Ω
    A-5 (B) - D-1
    Always
    Below 1 Ω
    A-7 (ICEI) - B-10 (SG)
    Always
    Below 1 Ω
    A-9 (COLI) - B-8 (CBT)
    Always
    Below 1 Ω
    A-10 (+B) - B-1 (+B)
    Always
    Below 1 Ω
    B-9 (BLW) - C-1
    Always
    Below 1 Ω
    B-9 (BLW) - D-2
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Vehicle Harness)
    *b
    Front view of wire harness connector
    (to Cool Box Air Conditioning Amplifier Assembly)
    *c
    Front view of wire harness connector
    (to Cooler Magnet Valve Assembly)
    *d
    Front view of wire harness connector
    (to Cooler Blower Motor)



NG
REPLACE NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY
OK


11.CHECK HARNESS AND CONNECTOR (COOLING BOX - AIR CONDITIONING AMPLIFIER)
  1. Disconnect the S9 cooling box assembly connector.

  1. Disconnect the H24 and H67 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S9-4 (ACT) - H67-12 (SWCB)
    Always
    Below 1 Ω
    S9-9 (COLI) - H24-26 (COOL)
    Always
    Below 1 Ω
    S9-4 (ACT) - Body ground
    Always
    10 kΩ or higher
    S9-9 (COLI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH - AIR CONDITIONING AMPLIFIER)
  1. Disconnect the H113 cooler control switch assembly connector.

  1. Disconnect the H67 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H113-7 (IND-) - H67-11 (LED)
    Always
    Below 1 Ω
    H113-7 (IND-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH - COOLING BOX)
  1. Disconnect the H113 cooler control switch assembly connector.

  1. Disconnect the S9 air cooling box assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H113-3 (-S) - S9-7 (ICEI)
    Always
    Below 1 Ω
    H113-6 (+S) - S9-2 (+S)
    Always
    Below 1 Ω
    H113-3 (-S) - Body ground
    Always
    10 kΩ or higher
    H113-6 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH - COMBINATION METER)
  1. Disconnect the H113 cooler control switch assembly connector.

  1. Disconnect the H37 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H113-4 (ILL-) - H37-37 (ILL-)
    Always
    Below 1 Ω
    H113-4 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)