AIR CONDITIONING SYSTEM > Rear Blower Motor Circuit |


| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR BLOWER MOTOR) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the rear blower motor operates.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Rear Blower Motor | Rear blower motor | Min.: 0, Max.: 31 | - |
| Result | Proceed to |
| Rear blower motor operates normally | A |
| Rear blower motor does not operate | B |
| Rear blower motor operates but does not change speed | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT FUSE (RR HTR) |
![]() |
Remove the RR HTR fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| RR HTR fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.INSPECT REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY |
![]() |
Remove the rear blower with fan motor sub-assembly (Click here).
Check the rear blower motor.
| Tester Connection | Specified Condition |
| Battery positive (+) → 2 (B) Battery negative (-) → 1 (L) | The rear blower motor operates smoothly. |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR - REAR BLOWER MOTOR CONTROL AND BODY GROUND) |
![]() |
Disconnect the P10 motor connector.
Disconnect the P11 control connector.
Measure the resistance according the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P10-2 (B) - P11-2 (VM) | Always | Below 1 Ω |
| P10-1 (L) - Body ground | Always | Below 1 Ω |
| P10-2 (B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - BATTERY AND BODY GROUND) |
![]() |
Disconnect the P11 control connector.
Measure the resistance and voltage according the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P11-6 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| P11-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - AIR CONDITIONING AMPLIFIER) |
![]() |
Disconnect the P11 control connector.
Disconnect the H67 amplifier connector.
Measure the resistance according the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P11-3 (SI)- H67-22 (BLWH) | Always | Below 1 Ω |
| P11-3 (SI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK BLOWER MOTOR CONTROL |
![]() |
Disconnect the H67 amplifier connector.
Measure the voltage according the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H67-22 (BLWH) - H67-20 (RGND) | Ignition switch ON Rear blower motor switch off | 4.5 to 7 V |
|
| ||||
| OK | |
| 8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Remove the air conditioning amplifier assembly with its connectors still connected (Click here).
Check the waveform of the air conditioning amplifier connector.
| Item | Content |
| Terminal No. (Symbol) | H67-22 (BLWH) - H67-20 (RGND) |
| Tool Setting | 1 V/DIV., 500 μsec./DIV. |
| Condition | Ignition switch ON Blower switch lo |
|
| ||||
| OK | ||
| ||