Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Suspension Control ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Suspension Control ECU Communication Stop Mode
Either condition is met:
  1. "Suspension Control (Air Suspension)" is not displayed on the "Bus Check" screen.
  2. "Suspension Control ECU Communication Stop Mode" in "DTC Communication Table" applies.
  1. Power source or inside of suspension control ECU
  2. Suspension control ECU CAN branch wire or connector
  3. Suspension control ECU
  1. For vehicles with an air suspension system.

WIRING DIAGRAM


C243207E02


C245789E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)


    C245665E01
  1. Disconnect the O16*1 or O19*2 suspension control ECU connector.

    1. *1: w/ AVS
    2. *2: w/o AVS

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ AVS 
    Tester Connection
    Switch Condition
    Specified Condition
    O16-7 (CANH) - O16-8 (CANL)
    Ignition switch off
    54 to 69 Ω
    w/o AVS 
    Tester Connection
    Switch Condition
    Specified Condition
    O19-29 (CANH) - O19-28 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *A
    w/ AVS
    *B
    w/o AVS
    *a
    Front view of wire harness connector
    (to Suspension Control ECU)



NG
REPAIR OR REPLACE SUSPENSION CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)


  1. Connect the cable to the negative (-) battery terminal.


    C245792E01


    Text in Illustration 
    *A
    w/ AVS
    *B
    w/o AVS
    *a
    Front view of wire harness connector
    (to Suspension Control ECU)
    -
    -

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. w/ AVS:
    Disconnect the O18 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ AVS 
    Tester Connection
    Condition
    Specified Condition
    O16-5 (GND) - Body ground
    Always
    Below 1 Ω
    O18-10 (GND) - Body ground
    Always
    Below 1 Ω
    w/o AVS 
    Tester Connection
    Condition
    Specified Condition
    O19-22 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    w/ AVS 
    Tester Connection
    Condition
    Specified Condition
    O16-3 (B) - Body ground
    Always
    11 to 14 V
    O16-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    w/o AVS 
    Tester Connection
    Condition
    Specified Condition
    O19-24 (B) - Body ground
    Always
    11 to 14 V
    O19-10 (IG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)