Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM

REAR SEAT ENTERTAINMENT SYSTEM > Sound Signal Circuit between Headphone Terminal and Television Display

for Preparation Click here


DESCRIPTION

This circuit sends a sound signal from the television display to the headphone terminal.

WIRING DIAGRAM


C242233E03


INSPECTION PROCEDURE

1.CHECK HEADPHONES
  1. Check the malfunctioning headphones.
    Result 
    Result
    Proceed to
    Malfunction in headphone terminal RH side
    A
    Malfunction in headphone terminal LH side
    B



B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - HEADPHONE TERMINAL RH)
  1. Disconnect the U13 television display assembly connector.

  1. Disconnect the S7 headphone terminal RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U13-26 (HP2R) - S7-1 (HP2R)
    Always
    Below 1 Ω
    U13-28 (HP2L) - S7-2 (HP2L)
    Always
    Below 1 Ω
    U13-27 (SLD6) - S7-3 (SG8)
    Always
    Below 1 Ω
    U13-26 (HP2R) - Body ground
    Always
    10 kΩ or higher
    U13-28 (HP2L) - Body ground
    Always
    10 kΩ or higher
    U13-27 (SLD6) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK TELEVISION DISPLAY ASSEMBLY


    E201128E07
  1. Remove the television display assembly connector still connected (Click here).

  1. Using an oscilloscope, check the waveform between each terminal and the body ground according to the conditions as shown in the table below.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    U13-26 (HP2R) - Body ground
    Audio sound being produced
    A waveform synchronized with sound is output
    U13-28 (HP2L) - Body ground

    Text in Illustration 
    *a
    Component with harness connected
    (Television Display Assembly)



NG
REPLACE TELEVISION DISPLAY ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - HEADPHONE TERMINAL LH)
  1. Disconnect the U13 television display assembly connector.

  1. Disconnect the S8 headphone terminal LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U13-12 (HP1R) - S8-1 (HP1R)
    Always
    Below 1 Ω
    U13-14 (HP1L) - S8-2 (HP1L)
    Always
    Below 1 Ω
    U13-13 (SLD5) - S8-3 (SG7)
    Always
    Below 1 Ω
    U13-12 (HP1R) - Body ground
    Always
    10 kΩ or higher
    U13-14 (HP1L) - Body ground
    Always
    10 kΩ or higher
    U13-13 (SLD5) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK TELEVISION DISPLAY ASSEMBLY


    E201128E08
  1. Remove the television display assembly connector still connected (Click here).

  1. Using an oscilloscope, check the waveform between each terminal and the body ground according to the conditions, as shown in the table below.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    U13-12 (HP1R) - Body ground
    Audio sound being produced
    A waveform synchronized with sound is output
    U13-14 (HP1L) - Body ground

    Text in Illustration 
    *a
    Component with harness connected
    (Television Display Assembly)



NG
REPLACE TELEVISION DISPLAY ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)