Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM

SEAT HEATER SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH (for Front Seat)


    B166556E06
  1. Disconnect the X12 heater control connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X12-6 (E) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    X12-1 (SWL) - X12-6 (E)
    Ignition switch ON
    Seat heater switch off
    Below 1 V
    Ignition switch ON
    Seat heater switch on
    11 to 14 V
    X12-4 (B) - X12-6 (E)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Connect the X12 heater control connector.



    B167840E08
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    X12-5 (THL) - Body ground
    Ignition switch ON
    Seat heater switch on, volume MIN → MAX (for Limited and SR5 grade)
    Seat heater switch on, volume 1 → 3 (for Platinum grade)
    Gradual increase between below 1 V and 11 to 14 V

    If the result is not as specified, the seat heater control may have a malfunction.



2. INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH (for Front Seat)


    B166556E07
  1. Disconnect the W8 heater control connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W8-6 (E) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    W8-1 (SWR) - W8-6 (E)
    Ignition switch ON
    Seat heater switch off
    Below 1 V
    Ignition switch ON
    Seat heater switch on
    11 to 14 V
    W8-4 (B1) - W8-6 (E)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Connect the W8 heater control connector.



    B167840E09
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    W8-5 (THR) - Body ground
    Ignition switch ON
    Seat heater switch on, volume MIN → MAX (for Limited and SR5 grade)
    Seat heater switch on, volume 1 → 3 (for Platinum grade)
    Gradual increase between below 1 V and 11 to 14 V

    If the result is not as specified, the seat heater control may have a malfunction.



3. INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH (for Rear No. 1 Seat)


    B188618E01
  1. Disconnect the O43 heater control connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O43-10 (SWL) - O43-13 (E)
    Seat heater LO switch off
    10 kΩ or higher
    Seat heater LO switch on
    Below 1 Ω
    O43-12 (HIL) - O43-13 (E)
    Seat heater HI switch off
    10 kΩ or higher
    Seat heater HI switch on
    Below 1 Ω
    O43-13 (E) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O43-1 (B) - O43-13 (E)
    Ignition switch ON
    11 to 14 V

    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Connect the O43 heater control connector.



    B188617E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Ignition switch ON
    Seat heater switch off
    Below 1 V
    Ignition switch ON
    Seat heater LO or HI switch on
    11 to 14 V

    HINT:
    When the heater reaches the specified temperature, the power turns off. If the result is not as specified, the seat heater control may have a malfunction.



4. INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH (for Rear No. 1 Seat)


    B188618E02
  1. Disconnect the P23 heater control connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    P23-10 (SWR) - P23-13 (TC)
    Seat heater LO switch off
    10 kΩ or higher
    Seat heater LO switch on
    Below 1 Ω
    P23-12 (HIR) - P23-13 (TC)
    Seat heater HI switch off
    10 kΩ or higher
    Seat heater HI switch on
    Below 1 Ω
    P23-13 (TC) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    P23-1 (B1) - P23-13 (TC)
    Ignition switch ON
    11 to 14 V

    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Connect the P23 heater control connector.



    B188617E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Ignition switch ON
    Seat heater switch off
    Below 1 V
    Ignition switch ON
    Seat heater LO or HI switch on
    11 to 14 V

    HINT:
    When the heater reaches the specified temperature, the power turns off. If the result is not as specified, the seat heater control may have a malfunction.