REAR EVAPORATOR TEMPERATURE SENSOR > REMOVAL |
| 1. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY |
![]() |
Raise the handle, detach the 4 guides and remove the No. 2 deck board.
| 2. REMOVE LUGGAGE COMPARTMENT TRIM BOX |
![]() |
Remove the 4 caps.
![]() |
Remove the 4 bolts and luggage compartment trim box.
| 3. REMOVE ROPE HOOK ASSEMBLY |
![]() |
Remove the bolt and rope hook.
| 4. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY |
![]() |
Detach the 5 clips and remove the No. 1 deck board.
| 5. REMOVE DECK BOARD REINFORCEMENT SUB-ASSEMBLY |
![]() |
Remove the 4 bolts and deck board reinforcement.
| 6. REMOVE DECK BOARD BRACKET |
![]() |
Remove the 2 bolts and deck board bracket.
| 7. REMOVE SEAT TRACK BRACKET FRONT COVER OUTER |
![]() |
Detach the 2 claws and 2 guides in the order shown in the illustration, and then remove the seat track bracket front cover outer.
| 8. REMOVE SEAT TRACK BRACKET FRONT COVER INNER |
![]() |
Detach the claw, clip and 2 guides in the order shown in the illustration, and then remove the seat track bracket front cover inner.
| 9. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat) |
![]() |
Remove the 2 bolts.
![]() |
Remove the 2 bolts.
Remove the connector.
Remove the rear No. 2 seat assembly RH from the vehicle.
| 10. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat) |
![]() |
Remove the 2 bolts.
![]() |
Remove the 2 bolts.
Remove the rear No. 2 seat assembly RH from the vehicle.
| 11. REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH |
![]() |
Detach the 2 clips and 5 claws, and remove the rear seat cushion hinge lower cover.
| 12. REMOVE REAR FLOOR STEP NO. 1 COVER |
![]() |
Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.
| 13. REMOVE REAR FLOOR STEP NO. 2 COVER |
![]() |
Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.
| 14. REMOVE REAR DOOR SCUFF PLATE RH |
![]() |
Remove the bolt.
Detach the 5 clips, 6 claws and 2 guides, and remove the rear door scuff plate front side.
![]() |
Remove the 2 bolts.
Detach the 5 clips and 2 claws, and remove the scuff plate rear side.
| 15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the rear door opening weatherstrip.
| 16. REMOVE ROPE HOOK ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.
![]() |
Remove the bolt and the rope hook.
| 17. REMOVE REAR FLOOR MAT SUPPORT PLATE |
![]() |
Detach the 5 clips and 4 claws, and remove the rear floor mat support plate.
| 18. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Standard) |
![]() |
Detach the 3 claws and remove the outer lap belt anchor cover.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.
Remove the 2 bolts and 2 clips.
Detach the 11 clips.
Disconnect the connector and remove the quarter trim panel.

| 19. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat) |
![]() |
Detach the 3 claws and remove the outer lap belt anchor cover.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.
Remove the 2 bolts and 2 clips.
Detach the 11 clips.
Disconnect the 3 connectors and remove the quarter trim panel.

| 20. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, detach the claw and remove the cover.
![]() |
Remove the bolt.
Detach the 5 clips.
Pass the rear seat outer belt floor anchor through the rear window side garnish, and remove the rear window side garnish.
| 21. REMOVE REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, detach the claw and remove the cover.
![]() |
Remove the bolt.
Detach the 5 clips.
Pass the rear seat outer belt floor anchor through the rear window No. 2 side garnish, and remove the rear window No. 2 side garnish.
| 22. REMOVE REAR SIDE NO. 2 AIR DUCT |
![]() |
Remove the 2 clips and the air duct.
| 23. REMOVE QUARTER TRIM BRACKET RH |
![]() |
Detach the clamp.
Remove the 2 bolts and the quarter trim bracket.
| 24. REMOVE COVER SUB-ASSEMBLY |
![]() |
Detach the 2 claws and remove the cover.
| 25. REMOVE REAR SIDE NO. 1 AIR DUCT |
![]() |
Detach the clamps.
Remove the clip and the air duct.
| 26. REMOVE REAR EVAPORATOR TEMPERATURE SENSOR (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY) |
![]() |
Disconnect the 2 connectors.
Detach the clamp and claw and remove the sensor.