Home › Vehicle Interior › HEATING / AIR CONDITIONING › REAR EVAPORATOR TEMPERATURE SENSOR

REAR EVAPORATOR TEMPERATURE SENSOR > REMOVAL

for Preparation Click here



1. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    B190118
  1. Raise the handle, detach the 4 guides and remove the No. 2 deck board.



2. REMOVE LUGGAGE COMPARTMENT TRIM BOX


    B194633
  1. Remove the 4 caps.



    B190116
  1. Remove the 4 bolts and luggage compartment trim box.



3. REMOVE ROPE HOOK ASSEMBLY


    B191405
  1. Remove the bolt and rope hook.

    HINT:
    Use the same procedure for both sides.



4. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Detach the 5 clips and remove the No. 1 deck board.



5. REMOVE DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Remove the 4 bolts and deck board reinforcement.



6. REMOVE DECK BOARD BRACKET


    B190119
  1. Remove the 2 bolts and deck board bracket.



7. REMOVE SEAT TRACK BRACKET FRONT COVER OUTER


    B191196E02
  1. Detach the 2 claws and 2 guides in the order shown in the illustration, and then remove the seat track bracket front cover outer.



8. REMOVE SEAT TRACK BRACKET FRONT COVER INNER


    B232092E01
  1. Detach the clip, claw and 2 guides in the order shown in the illustration, and then remove the seat track bracket front cover inner.



9. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat)


    B191200
  1. Remove the 2 bolts.



    B191203
  1. Remove the 2 bolts.

  1. Remove the connector.

  1. Remove the rear No. 2 seat assembly RH from the vehicle.

    NOTICE:
    Be careful not to damage the vehicle body.



10. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat)


    B191200
  1. Remove the 2 bolts.



    B191201
  1. Remove the 2 bolts.

  1. Remove the rear No. 2 seat assembly RH from the vehicle.

    NOTICE:
    Be careful not to damage the vehicle body.



11. REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH


    B191794
  1. Detach the 2 clips and 5 claws, and remove the rear seat cushion hinge lower cover.



12. REMOVE REAR FLOOR STEP NO. 1 COVER


    B191403E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



13. REMOVE REAR FLOOR STEP NO. 2 COVER


    B193052E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



14. REMOVE REAR DOOR SCUFF PLATE RH


    B190151
  1. Detach the 9 claws and remove the scuff plate.



15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B191804
  1. Remove the rear door opening weatherstrip.



16. REMOVE ROPE HOOK ASSEMBLY

HINT:
Use the same procedure for both sides.



    B190140E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.



    B190141
  1. Remove the bolt and the rope hook.



17. REMOVE REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Detach the 5 clips and 4 claws, and remove the rear floor mat support plate.



18. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Standard)


    B190145
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the connector and remove the quarter trim panel.


    B219907



19. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)


    B190145
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the 3 connectors and remove the quarter trim panel.


    B222459



20. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH


    B190121E02
  1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and remove the cover.



    B190124
  1. Remove the bolt.

  1. Detach the 5 clips.

  1. Pass the rear seat outer belt floor anchor through the rear window side garnish, and remove the rear window side garnish.



21. REMOVE REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH


    B190122E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and remove the cover.



    B190123
  1. Remove the bolt.

  1. Detach the 5 clips.

  1. Pass the rear seat outer belt floor anchor through the rear window No. 2 side garnish, and remove the rear window No. 2 side garnish.



22. REMOVE REAR SIDE NO. 2 AIR DUCT


    E181294
  1. Remove the 2 clips and the air duct.



23. REMOVE QUARTER TRIM BRACKET RH


    I104301
  1. Detach the clamp.

  1. Remove the 2 bolts and the quarter trim bracket.



24. REMOVE COVER SUB-ASSEMBLY


    I104302
  1. Detach the 2 claws and remove the cover.



25. REMOVE REAR SIDE NO. 1 AIR DUCT


    I104303
  1. Detach the clamps.

  1. Remove the clip and the air duct.



26. REMOVE REAR EVAPORATOR TEMPERATURE SENSOR (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY)


E181301
  1. Disconnect the 2 connectors.

  1. Detach the clamp and claw and remove the sensor.