Home › Vehicle Interior › INTERIOR PANELS / TRIM › FRONT CONSOLE BOX (w/ Cool Box)

FRONT CONSOLE BOX (w/ Cool Box) > DISASSEMBLY

for Preparation Click here



1. REMOVE CONSOLE BOX REAR COVER


    B188237
  1. Detach the 2 claws and remove the console box rear cover.



2. REMOVE INSTRUMENT PANEL CUP HOLDER ASSEMBLY


    B188238
  1. Detach the 4 clips and remove the cup holder.



3. REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY (w/o Rear Seat Entertainment System)


    B219733
  1. Detach the 6 clips and remove the console rear end panel.



    B219734
  1. Disconnect the 2 connectors.

  1. Detach the 2 wire harness clamps.



4. REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY (w/ Rear Seat Entertainment System)


    B219732
  1. Detach the 6 clips and remove the console rear end panel.



    B219737
  1. Disconnect the 4 connectors.

  1. Detach the 2 wire harness clamps.



    B219808
  1. Detach the 2 wire harness clamps and 4 claws, and remove the 2 headphone terminals.



5. REMOVE CONSOLE BOX REGISTER BEZEL


    B188239
  1. Remove the 4 screws.

  1. Detach the 4 claws and remove the console box register bezel.



6. REMOVE CONSOLE REAR END PANEL GARNISH


    B188241
  1. Remove the 4 screws and console rear end panel garnish.



7. REMOVE CONSOLE COMPARTMENT DOOR CUSHION


    B188242
  1. Remove the 2 cushions.



8. REMOVE CONSOLE COMPARTMENT DOOR SUB-ASSEMBLY


    B262030
  1. Remove the 8 screws and console compartment door.



9. REMOVE CONSOLE BOX CUSHION


    B188229
  1. Remove the 2 cushions.



10. REMOVE CONSOLE BOX WIRE


    B262031
  1. Detach the 5 clamps and remove the console box wire.



11. REMOVE POWER POINT SOCKET ASSEMBLY
  1. Disconnect the connector.



    E212283E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the power point socket assembly.
    Text in Illustration 
    *1
    Protective Tape



12. REMOVE POWER OUTLET SOCKET COVER NO.2


    E162363
  1. Disengage the 2 claws and remove the power outlet socket cover.



13. REMOVE NO. 2 COOL BOX PACKING


    B262062
  1. Apply protective tape, as shown in the illustration.
    Text in Illustration 
    V100155
    Protective Tape



    B262032
  1. Remove the No. 2 cool box packing.



14. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY


    B262033
  1. Remove the 8 screws and rear console box sub-assembly.



15. REMOVE COOL BOX AIR CONDITIONING AMPLIFIER ASSEMBLY


    B262034
  1. Disconnect the connector.

  1. Remove the 2 screws and cool box air conditioning amplifier assembly.



16. REMOVE NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY


    B262035
  1. Remove the packing.



    B262036
  1. Disconnect the 3 connectors and detach the clamp.



17. REMOVE COOLER BRACKET


    B262037
  1. Remove the 2 screws and cooler bracket.



18. REMOVE COOLER REFRIGERANT LIQUID PIPE G


    B262038
  1. Remove the bolt, 2 screws and cooler refrigerant liquid pipe G.



    B262039
  1. Remove the O-ring from the cooler refrigerant liquid pipe G.



19. REMOVE COOL BOX BLOWER WITH FAN MOTOR SUB-ASSEMBLY


    B262040
  1. Remove the screw.

  1. Remove the 5 holding springs and lower cooling unit case.



    B262041
  1. Remove the cooling unit case RH.



    B262042
  1. Remove the cooling unit case LH.



    B262043
  1. Remove the blower motor with evaporator sub-assembly.



    B262044
  1. Remove the 2 packings.



    B262045
  1. Remove the 2 screws.

  1. Detach the 4 claws and guide and remove the cool box blower with fan motor sub-assembly.



20. REMOVE COOLER REFRIGERANT LIQUID PIPE F


    B262046E01
  1. Put matchmarks on the cooler refrigerant liquid pipe F and the cooler magnet valve assembly.
    Text in Illustration 
    *a
    Matchmark



    B262047E01
  1. Using SST, disconnect the cooler refrigerant liquid pipe F from the cooler magnet valve assembly while holding the cooler magnet valve assembly with a wrench.

    SST
    09922-10010  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Do not kink or damage the cooler refrigerant liquid pipe F.



    B262048
  1. Remove the O-ring from the cooler refrigerant liquid pipe F.



21. REMOVE COOLER MAGNET VALVE ASSEMBLY


    B262049E01
  1. Put matchmarks on the cooler magnet valve assembly and the evaporator sub-assembly.
    Text in Illustration 
    *a
    Matchmark



    B262050E01
  1. Using SST, disconnect the cooler magnet valve assembly from the evaporator sub-assembly while holding the cooler magnet valve assembly with a wrench.

    SST
    09922-10010  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Do not kink or damage the evaporator sub-assembly.



    B262051
  1. Remove the O-ring from the evaporator sub-assembly.



22. REMOVE COOLER THERMISTOR


    B262052
  1. Detach the 5 guides and remove the cooler thermistor.