FRONT CONSOLE BOX (w/ Cool Box) > REASSEMBLY |
| 1. INSTALL COOLER THERMISTOR |
![]() |
Attach the 5 guides and install the cooler thermistor.
| 2. INSTALL COOLER MAGNET VALVE ASSEMBLY |
![]() |
Sufficiently apply compressor oil to a new O-ring and to the fitting surfaces of the evaporator sub-assembly.
![]() |
Align the matchmarks and install the cooler magnet valve assembly onto the evaporator sub-assembly.
| *a | Matchmark |
![]() |
Using SST, connect the evaporator sub-assembly to the cooler magnet valve assembly while holding the cooler magnet valve assembly with a wrench.
| *a | Hold |
| *b | Turn |
| *c | Fulcrum Length |
| 3. INSTALL COOLER REFRIGERANT LIQUID PIPE F |
![]() |
Sufficiently apply compressor oil to a new O-ring and to the fitting surfaces of the cooler refrigerant liquid pipe F.
![]() |
Align the matchmarks and install the cooler refrigerant liquid pipe F onto the cooler magnet valve assembly.
| *a | Matchmark |
![]() |
Using SST, connect the cooler refrigerant liquid pipe F to the cooler magnet valve assembly while holding the cooler magnet valve assembly with a wrench.
| *a | Hold |
| *b | Turn |
| *c | Fulcrum Length |
| 4. INSTALL COOL BOX BLOWER WITH FAN MOTOR SUB-ASSEMBLY |
![]() |
Attach the 4 claws and guide install the cool box blower with fan motor sub-assembly.
Install the 2 screws.
![]() |
Install 2 new packings.
![]() |
Install the blower motor with evaporator sub-assembly as shown in the illustration.
![]() |
Install the cooling unit case LH as shown in the illustration.
![]() |
Install the cooling unit case RH as shown in the illustration.
![]() |
Attach the 2 guides and install the lower cooling unit case with the 5 holding springs as shown in the illustration.
Install the screw.
| 5. INSTALL COOLER REFRIGERANT LIQUID PIPE G |
![]() |
Sufficiently apply compressor oil to a new O-ring and to the fitting surfaces of the cooler refrigerant liquid pipe G.
![]() |
Install the cooler refrigerant liquid pipe G with the bolt and 2 screws.
| 6. INSTALL COOLER BRACKET |
![]() |
Install the bracket with the 2 screws.
| 7. INSTALL NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY |
![]() |
Attach the clamp and connect the 3 connectors.
![]() |
Install a new packing.
| 8. INSTALL COOL BOX AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Install the cool box air conditioning amplifier assembly with the 2 screws.
Connect the connector.
| 9. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY |
![]() |
Install the rear console box sub-assembly with the 8 screws.
| 10. INSTALL NO. 2 COOL BOX PACKING |
![]() |
Install a new No. 2 cool box packing.
| 11. INSTALL POWER OUTLET SOCKET COVER NO.2 |
Engage the 2 claws to install the power outlet socket cover.
| 12. INSTALL POWER POINT SOCKET ASSEMBLY |
![]() |
Engage the 2 claws to install the power point socket assembly.
Connect the connector.
| 13. INSTALL CONSOLE BOX WIRE |
![]() |
Attach the 5 clamps to install the console box wire.
| 14. INSTALL CONSOLE BOX CUSHION |
![]() |
Install the 2 cushions.
| 15. INSTALL CONSOLE COMPARTMENT DOOR SUB-ASSEMBLY |
![]() |
Install the console compartment door with the 8 screws.
| 16. INSTALL CONSOLE COMPARTMENT DOOR CUSHION |
![]() |
Install the 2 cushions.
| 17. INSTALL CONSOLE REAR END PANEL GARNISH |
![]() |
Install the console rear end panel garnish with the 4 screws.
| 18. INSTALL CONSOLE BOX REGISTER BEZEL |
![]() |
Attach the 4 claws to install the console box register bezel.
Install the 4 screws.
| 19. INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY (w/o Rear Seat Entertainment System) |
![]() |
Attach the 2 wire harness clamps.
Connect the 2 connectors.
![]() |
Attach the 6 clips to install the console rear end panel.
| 20. INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY (w/ Rear Seat Entertainment System) |
![]() |
Attach the 4 claws and 2 wire harness clamps to install the 2 headphone terminals.
![]() |
Attach the 2 wire harness clamps.
Connect the 4 connectors.
![]() |
Attach the 6 clips to install the console rear end panel.
| 21. INSTALL INSTRUMENT PANEL CUP HOLDER ASSEMBLY |
![]() |
Attach the 4 clips to install the cup holder.
| 22. INSTALL CONSOLE BOX REAR COVER |
![]() |
Attach the 2 claws to install the console box rear cover.