Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM

REAR POWER SEAT CONTROL SYSTEM > Position Sensor Circuit

for Preparation Click here


DESCRIPTION

The fold seat control ECU receives switch operation signals from the rear power seat switch and fold seat switch, and activates the power seat motor. At this time, the Hall IC (seatback position sensor) detects the actuation of the seatback and sends a seatback actuation signal to the fold seat control ECU. The fold seat control ECU uses signals from the Hall IC (seatback position sensor) to detect if an object is caught or if any other abnormal condition has occurred.

WIRING DIAGRAM


B193762E03


INSPECTION PROCEDURE

1.CHECK FOLD SEAT CONTROL ECU (SV2 TERMINAL)


    B193667E09
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    O34-25 (SV2) - O34-36 (SG2)
    Back door open
    11 to 14 V
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    P20-25 (SV2) - P20-36 (SG2)
    Back door open
    11 to 14 V



NG
REPLACE FOLD SEAT CONTROL ECU (Click here)
OK


2.CHECK FOLD SEAT CONTROL ECU (POSITION SENSOR SIGNAL)


    B193667E10
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    O34-22 (SRCL) - O34-36 (SG2)
    Motor is operating
    Below 1 V ←→ 11 to 14 V
    Pulse generation
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    P20-22 (SRCL) - P20-36 (SG2)
    Motor is operating
    Below 1 V ←→ 11 to 14 V
    Pulse generation



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 1 POWER SEAT MOTOR)


    B195052E02
  1. Disconnect the O34 or P20 ECU connector.

  1. Disconnect the a2 or Y2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    O34-22 (SRCL) - a2-1 (HLS)
    Always
    Below 1 Ω
    O34-22 (SRCL) - Body ground
    Always
    10 kΩ or higher
    O34-25 (SV2) - a2-3 (HLV)
    Always
    Below 1 Ω
    O34-25 (SV2) - Body ground
    Always
    10 kΩ or higher
    O34-36 (SG2) - a2-2 (HLG)
    Always
    Below 1 Ω
    O34-36 (SG2) - Body ground
    Always
    10 kΩ or higher
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    P20-22 (SRCL) - Y2-1 (HLS)
    Always
    Below 1 Ω
    P20-22 (SRCL) - Body ground
    Always
    10 kΩ or higher
    P20-25 (SV2) - Y2-3 (HLV)
    Always
    Below 1 Ω
    P20-25 (SV2) - Body ground
    Always
    10 kΩ or higher
    P20-36 (SG2) - Y2-2 (HLG)
    Always
    Below 1 Ω
    P20-36 (SG2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 POWER SEAT MOTOR (Click here)