Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER

REAR BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL REAR BUMPER BAR BRACKET LH


B191669
  1. Install the rear bumper bar bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



2. INSTALL REAR BUMPER BAR BRACKET RH

HINT:
Use the same procedure as for the LH side.



3. INSTALL REAR BUMPER ARM BRACKET LH


B191668
  1. Install the rear bumper arm bracket with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL REAR BUMPER ARM BRACKET RH

HINT:
Use the same procedure as for the LH side.



5. INSTALL REAR FLOOR STAY BRACKET LH


B191667
  1. Install the rear floor stay with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



6. INSTALL REAR FLOOR STAY BRACKET RH

HINT:
Use the same procedure as for the LH side.



7. INSTALL REAR BUMPER ENERGY ABSORBER


B191666
  1. Install the rear bumper energy absorber.



8. INSTALL REAR BUMPER END RETAINER LH


B191665
  1. Attach the 2 claws to install the rear bumper end retainer.

  1. Install the screw.



9. INSTALL REAR BUMPER END RETAINER RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL REAR BUMPER UPPER RETAINER LH


B191664
  1. Attach the 4 claws to install the rear bumper upper retainer.

  1. Install the 3 screws.



11. INSTALL REAR BUMPER UPPER RETAINER RH

HINT:
Use the same procedure as for the LH side.



12. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor retainer on the other side.



    E146471E01
  1. Install the ultrasonic sensor retainer to the rear bumper.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.



13. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor on the other side.



    E146472
  1. Attach the 2 claws to install the ultrasonic sensor.

  1. Connect the connector.



14. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to install the No. 2 ultrasonic sensor retainer on the other side.



    E146473E01
  1. Install the ultrasonic sensor retainer to the rear bumper.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.



15. INSTALL NO. 2 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to install the No. 2 ultrasonic sensor on the other side.



    E146466
  1. Attach the 2 claws to install the ultrasonic sensor.

  1. Connect the connector.



16. INSTALL NO. 2 FRAME WIRE (w/ TOYOTA Parking Assist-sensor System)


B191663
  1. Connect the 6 harness clamps and No. 2 frame wire.

  1. Connect the 4 connectors.



17. INSTALL GROMMET


B191661E01
  1. Install the 6 grommets.



18. INSTALL REAR BUMPER PAD LH


B191660E01
  1. Apply Primer G to the installation part of the rear bumper pad.

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

  1. Install the new rear bumper pad onto the rear bumper cover, as shown in the illustration.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



19. INSTALL REAR BUMPER PAD RH

HINT:
Use the same procedure as for the LH side.



20. INSTALL REAR BUMPER LOWER COVER


B191658E01
  1. Apply Primer G to the installation part of the rear bumper lower cover.

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

  1. Install the new rear bumper lower cover onto the rear bumper cover, as shown in the illustration.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



21. INSTALL REFLEX REFLECTOR ASSEMBLY LH


B191657
  1. Install the reflex reflector with the nut.



22. INSTALL REFLEX REFLECTOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.