Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF RACK

ROOF RACK > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL ROOF RACK LEG CENTER CUSHION LH


B195992
  1. Attach the 3 claws to install the roof rack leg center cushion.



2. INSTALL ROOF RACK LEG CENTER CUSHION RH

HINT:
Use the same procedure as for the LH side.



3. INSTALL ROOF RACK LEG REAR CUSHION LH


B191697
  1. Attach the 2 claws to install the roof rack leg rear cushion.



4. INSTALL ROOF RACK LEG REAR CUSHION RH

HINT:
Use the same procedure as for the LH side.



5. INSTALL ROOF RACK LEG FRONT CUSHION LH


B191696
  1. Attach the 2 claws to install the roof rack leg front cushion.



6. INSTALL ROOF RACK LEG FRONT CUSHION RH

HINT:
Use the same procedure as for the LH side.



7. INSTALL ROOF RACK REAR LEG LH


B191695
  1. Install the roof rack rear leg with the 2 screws.



8. INSTALL ROOF RACK REAR LEG RH

HINT:
Use the same procedure as for the LH side.



9. INSTALL ROOF RACK FRONT LEG LH


B191693
  1. Install the roof rack front leg with the 2 screws.



10. INSTALL ROOF RACK FRONT LEG RH

HINT:
Use the same procedure as for the LH side.



11. INSTALL ROOF RACK CENTER SUPPORT SUB-ASSEMBLY LH


B191692
  1. Using a "TORX" socket wrench T30, install the roof rack center support LH with the 2 screws.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



12. INSTALL ROOF CARRIER SUB-ASSEMBLY LH


B219631
  1. Using a "TORX" socket wrench T30, install the roof carrier LH with the 6 screws.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



13. INSTALL ROOF RACK CENTER SUPPORT SUB-ASSEMBLY RH


B191689
  1. Using a "TORX" socket wrench T30, install the roof rack center support RH with the 2 screws.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



14. INSTALL ROOF CARRIER SUB-ASSEMBLY RH
  1. Provisionally install the roof rack center support into the roof carrier.



    B219630
  1. Using a "TORX" socket wrench T30, install the roof carrier RH with the 6 screws.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



15. INSTALL ROOF RACK LEG REAR COVER LH


B191686
  1. Attach the 3 claws and clip to install the roof rack leg rear cover.



16. INSTALL ROOF RACK LEG REAR COVER RH

HINT:
Use the same procedure as for the LH side.



17. INSTALL ROOF RACK LEG CENTER COVER LH


B219629
  1. Attach the 2 claws and clip to install the roof rack leg center cover.



18. INSTALL ROOF RACK LEG CENTER COVER RH

HINT:
Use the same procedure as for the LH side.



19. INSTALL ROOF RACK LEG FRONT COVER LH


B191684
  1. Attach the 3 claws and clip to install the roof rack leg front cover.



20. INSTALL ROOF RACK LEG FRONT COVER RH

HINT:
Use the same procedure as for the LH side.