Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR

POWER WINDOW REGULATOR MOTOR > INSTALLATION

for Preparation Click here



1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B191728
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using a T25 "TORX" socket wrench, install the power window regulator motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the rear door window regulator sub-assembly.

    NOTICE:
    Do not apply grease to the front door window regulator spring.



    B192108E01
  1. Loosely install the bolt labeled A onto the window regulator sub-assembly.

  1. Insert the rear door window regulator sub-assembly into the door panel. Provisionally tighten bolt A to hang the rear door window regulator sub-assembly on the door panel.

    NOTICE:
    Do not drop the front door window regulator sub-assembly as it may be damaged.

  1. Install the front door window regulator sub-assembly with the 5 bolts, and tighten the bolt labeled A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B190588
  1. Install the rear door glass sub-assembly onto the rear door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL REAR DOOR WINDOW FRONT GUIDE SUB-ASSEMBLY


    B190587
  1. Install the rear door window guide front sub-assembly with the 2 bolts

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



5. INSTALL REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY


B190586
  1. Install the rear door window frame rear lower sub-assembly with the nut and 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



6. INSTALL REAR DOOR GLASS RUN


    B190585
  1. Install the rear door glass run.



7. INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP

HINT:
Use the same procedure as for the LH side .



8. INSTALL REAR DOOR WINDOW FRAME REAR MOULDING

HINT:
Use the same procedure as for the LH side .



9. INSTALL REAR DOOR SERVICE HOLE COVER


    B195022
  1. Apply butyl tape to the door panel, then install a new rear door service hole cover as shown in the illustration.

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B190584
  1. Attach the clamps and connect the connectors.



10. INSTALL REAR DOOR TRIM NO. 2 BRACKET


    B190583
  1. Install the rear door trim No. 2 bracket with the 2 screws.



11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B190580
  1. Connect the rear door lock remote control cable and the rear door inside locking cable.

  1. Connect the connector.



    B190579
  1. Attach the 9 clips to install the rear door trim board sub-assembly.



    B190578
  1. Tighten the 2 screws.

  1. Install the rear door armrest cover.



12. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


B190576
  1. Attach the 4 claws to install the rear door inside handle bezel plug.



13. INSTALL REAR DOOR ARMREST BASE UPPER PANEL
  1. Connect the connector.



    B190574
  1. Attach the 2 clips and 5 claws to install the rear door armrest base upper panel.



14. INSTALL REAR DOOR FRAME GARNISH


    B190577
  1. Attach the 6 clips to install the rear door frame garnish.



15. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B191727
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using a T25 "TORX" socket wrench, install the front power window regulator motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



16. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B190554E01
  1. Loosely screw bolt A onto the front door window regulator

  1. Insert the front door window regulator into the door panel. Provisionally tighten bolt A to hang the front door window regulator on the door panel.

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Install the front door window regulator with the 5 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



17. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    B192559
  1. Insert the door glass into the door panel by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.



    B190553
  1. Install the front door glass onto the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



18. INSTALL FRONT DOOR GLASS RUN


    B190552
  1. Install the front door glass run.



19. INSTALL FRONT DOOR SERVICE HOLE COVER


    B195024
  1. Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B190551
  1. Attach the clamps and connect the connectors.



20. INSTALL FRONT DOOR NO. 1 TRIM BRACKET


    B190549
  1. Install the front door No. 1 trim bracket with the 2 screws.



21. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:
Use the same procedure as for the LH side .



22. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

HINT:
Use the same procedure as for the LH side .



23. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connectors.



    B190543
  1. Connect the front door lock remote control cable and the front door inside locking cable.



    B190542
  1. Attach the 10 clips to install the front door trim board sub-assembly.



    B190541
  1. Tighten the 2 screws.

  1. Install the front door armrest cover.



24. INSTALL FRONT ARMREST BASE UPPER PANEL


B190537
  1. Connect the connector.

  1. Attach the 2 clips and 5 claws to install the front armrest base upper panel.



25. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B190540
  1. Attach the 4 claws to install the front door inside handle bezel plug



26. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


B194240
  1. Attach the 3 clips to install the front door lower frame bracket garnish.



27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).