POWER WINDOW REGULATOR MOTOR > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Detach the 3 clips and remove the front door lower frame bracket garnish.
| 3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, detach the 4 claws and remove the front door inside handle bezel plug.
| 4. REMOVE FRONT ARMREST BASE UPPER PANEL |
![]() |
Detach the 2 clips and 5 claws and remove the front armrest base upper panel.
Disconnect the connector.
| 5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Remove the front door armrest cover.
Remove the 2 screws.
![]() |
Detach the 10 clips.
Disconnect the connector.
![]() |
Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board sub-assembly.
| 6. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY |
| 7. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY |
| 8. REMOVE FRONT DOOR NO. 1 TRIM BRACKET |
![]() |
Remove the 2 screws and remove the front door No. 1 trim bracket.
| 9. REMOVE FRONT DOOR SERVICE HOLE COVER |
![]() |
Disconnect the connectors and detach the clamps.
![]() |
Remove the front door service hole cover.
| 10. REMOVE FRONT DOOR GLASS RUN |
![]() |
Remove the front door glass run.
| 11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Provisionally install the power window switch.
Move the front door glass until the 2 bolts can be seen through the service holes.
Remove the 2 bolts.
![]() |
Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.
Remove the power window switch.
| 12. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
![]() |
Disconnect the connector.
Loosen bolt A.
Remove the 5 bolts, then remove the front door window regulator sub-assembly.
| 13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.
| 14. REMOVE REAR DOOR FRAME GARNISH |
![]() |
Detach the 6 clips and remove the rear door frame garnish.
| 15. REMOVE REAR DOOR ARMREST BASE UPPER PANEL |
![]() |
Detach the 2 clips and 5 claws and remove the rear door armrest base upper panel.
| 16. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, detach the 4 claws and remove the rear door inside handle bezel plug.
| 17. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Remove the rear door armrest cover.
Remove the 2 screws.
![]() |
Detach the 9 clips.
Disconnect the connector.
![]() |
Disconnect the rear door lock remote control cable and the rear door inside locking cable and remove the rear door trim board sub-assembly.
| 18. REMOVE REAR DOOR TRIM NO. 2 BRACKET |
![]() |
Remove the 2 screws and remove the rear door trim No. 2 bracket.
| 19. REMOVE REAR DOOR SERVICE HOLE COVER |
![]() |
Detach the clamps and disconnect the connectors.
![]() |
Remove the rear door service hole cover.
| 20. REMOVE REAR DOOR WINDOW FRAME REAR MOULDING |
| 21. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP |
| 22. REMOVE REAR DOOR GLASS RUN |
![]() |
Remove the rear door glass run.
| 23. REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Loosen nut A.
Remove the 3 bolts and rear door window frame rear lower sub-assembly.
| 24. REMOVE REAR DOOR WINDOW FRONT GUIDE SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and rear door window guide front sub-assembly.
| 25. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Provisionally install the power window switch.
Move the rear door glass until the 2 bolts can be seen through the service holes.
Remove the 2 bolts and remove the rear door glass sub-assembly.
| 26. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY |
![]() |
Disconnect the connector.
Loosen the bolt labeled A.
Remove the 5 bolts and remove the rear door window regulator sub-assembly.
Remove the bolt labeled A from the front door window regulator assembly.
| 27. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.