Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR

POWER WINDOW REGULATOR MOTOR > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the RH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    B190538
  1. Detach the 3 clips and remove the front door lower frame bracket garnish.

  1. Disconnect the connector.



3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B190539
  1. Using a moulding remover, detach the 4 claws and remove the front door inside handle bezel plug.



4. REMOVE FRONT ARMREST BASE UPPER PANEL


    B190537
  1. Detach the 2 clips and 5 claws and remove the front armrest base upper panel.

  1. Disconnect the connector.



5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


B190541
  1. Remove the front door armrest cover.

  1. Remove the 2 screws.



    B190542
  1. Detach the 10 clips.

  1. Disconnect the connector.



    B190543
  1. Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board sub-assembly.



6. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

HINT:
Use the same procedure as for the LH side (Click here).



7. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:
Use the same procedure as for the LH side .



8. REMOVE FRONT DOOR NO. 1 TRIM BRACKET


    B190549
  1. Remove the 2 screws and remove the front door No. 1 trim bracket.



9. REMOVE FRONT DOOR SERVICE HOLE COVER


    B190551
  1. Disconnect the connectors and detach the clamps.



    B195025
  1. Remove the front door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



10. REMOVE FRONT DOOR GLASS RUN


    B190552
  1. Remove the front door glass run.



11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


B190553
  1. Provisionally install the power window switch.

  1. Move the front door glass until the 2 bolts can be seen through the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Do not drop or damage the front door glass subassembly when removing the bolts.



    B195026
  1. Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the front door glass subassembly.

  1. Remove the power window switch.



12. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY


    B190554E01
  1. Disconnect the connector.

  1. Loosen bolt A.

  1. Remove the 5 bolts, then remove the front door window regulator sub-assembly.

    NOTICE:
    Do not drop or damage the front door window regulator sub-assembly when removing the bolts.

    HINT:
    Remove the front door window regulator sub-assembly through the service hole.



13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B191727
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.



14. REMOVE REAR DOOR FRAME GARNISH


    B190577
  1. Detach the 6 clips and remove the rear door frame garnish.



15. REMOVE REAR DOOR ARMREST BASE UPPER PANEL


    B190574
  1. Detach the 2 clips and 5 claws and remove the rear door armrest base upper panel.



16. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B190575
  1. Using a moulding remover, detach the 4 claws and remove the rear door inside handle bezel plug.



17. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


B190578
  1. Remove the rear door armrest cover.

  1. Remove the 2 screws.



    B190579
  1. Detach the 9 clips.

  1. Disconnect the connector.



    B190580
  1. Disconnect the rear door lock remote control cable and the rear door inside locking cable and remove the rear door trim board sub-assembly.



18. REMOVE REAR DOOR TRIM NO. 2 BRACKET


    B190583
  1. Remove the 2 screws and remove the rear door trim No. 2 bracket.



19. REMOVE REAR DOOR SERVICE HOLE COVER


    B190584
  1. Detach the clamps and disconnect the connectors.



    B195023
  1. Remove the rear door service hole cover.

    NOTICE:
    Remove any tape remaining on the door.



20. REMOVE REAR DOOR WINDOW FRAME REAR MOULDING

HINT:
Use the same procedure as for the LH side .



21. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP

HINT:
Use the same procedure as for the LH side .



22. REMOVE REAR DOOR GLASS RUN


    B190585
  1. Remove the rear door glass run.



23. REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY


    B190586E01
  1. Loosen nut A.

  1. Remove the 3 bolts and rear door window frame rear lower sub-assembly.

    NOTICE:
    Do not drop or damage the rear door window frame rear lower sub-assembly.



24. REMOVE REAR DOOR WINDOW FRONT GUIDE SUB-ASSEMBLY


    B190587
  1. Remove the 2 bolts and rear door window guide front sub-assembly.

    NOTICE:
    Do not drop or damage the rear door window guide front sub-assembly when removing the bolts.



25. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


B190588
  1. Provisionally install the power window switch.

  1. Move the rear door glass until the 2 bolts can be seen through the service holes.

  1. Remove the 2 bolts and remove the rear door glass sub-assembly.

    NOTICE:
    Do not damage the door glass.



26. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    B192108E01
  1. Disconnect the connector.

  1. Loosen the bolt labeled A.

  1. Remove the 5 bolts and remove the rear door window regulator sub-assembly.

    NOTICE:
    Do not damage the rear door window regulator sub-assembly.

  1. Remove the bolt labeled A from the front door window regulator assembly.



27. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B191728
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.