Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR POWER WINDOW MOTOR

BACK DOOR POWER WINDOW MOTOR > INSTALLATION

for Preparation Click here



1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

HINT:
  1. To prevent the drum and cable from coming off, do not tilt the drum, subject it to shocks or use force on it.
  2. If the cable comes off the drum, do not rewind the cable and do not reuse it.
  3. After installing the window regulator, do not operate it by itself, because some types of regulator do not have a stopper.



    B062867E01
  1. Apply MP grease to the as shown in the illustration.



    B062868
  1. With the holding tool installed, match the holding tool with the motor housing.



    B062869
  1. Push down on the wire guide and drum, and insert the drum into the motor housing.

    NOTICE:
    If you can not insert the drum into the motor, slowly slide the bracket for installing the glass, and insert the drum while aligning the drive shaft of the motor with the drum.



    B062870
  1. Install the power window regulator base plate with the 2 screws.

  1. Install the power window regulator motor onto the back door power window regulator.



2. INSTALL BACK DOOR POWER WINDOW REGULATOR ASSEMBLY


B190529E01
  1. Apply MP grease to the sliding and rotating areas of the back door power window regulator.

  1. Insert the back door power window regulator into the door panel. Provisionally tighten nut A to hang the back door power window regulator on the door panel.

    NOTICE:
    Do not drop the back door power window regulator as it may be damaged.

  1. Install the back door power window regulator with the 5 nuts, and tighten nut A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



3. INSTALL BACK DOOR GLASS


B190528
  1. Install the back door glass onto the back door power window regulator with the 4 bolts.

    NOTICE:
    Do not damage the glass.

  1. Connect the 2 connectors.



    B190513
  1. Install the hole plug.



4. INSTALL BACK DOOR GLASS RUN


B190527
  1. Install a new back door glass run.



5. INSTALL BACK DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B195693
  1. Attach the 9 claws to install the back door glass outer weatherstrip.



6. INSTALL BACK DOOR OUTSIDE MOULDING LH


    B191708
  1. Attach the 5 clips to install a new back door outside moulding.



7. INSTALL BACK DOOR OUTSIDE MOULDING RH

HINT:
Use the same procedure as for the LH side.



8. INSTALL REAR WIPER STOPPER


B190526
  1. Attach the claw and guide to install the liner wiper step.



9. INSTALL REAR WIPER MOTOR GROMMET


E139081E02
  1. Apply MP grease to the entire surface of the wiper motor grommet lip.

    HINT:
    Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



    E162547E01
  1. Install the rear wiper motor grommet with the mark directed up.



10. INSTALL REAR WIPER MOTOR ASSEMBLY


    E161698
  1. Install the rear wiper motor with the 3 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector and clamp.



11. INSTALL REAR WIPER BLADE ASSEMBLY


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, and then stop the windshield wiper motor in the automatic stop position.



    B223787E01
  1. With the rear wiper blade and linear wiper step in the positions shown in the illustration, install the rear wiper blade assembly with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    Hold the arm hinge down by hand while tightening the nut.



    B223788E01
  1. Place the rear wiper blade assembly in the automatic stop position.



12. INSTALL REAR WIPER ARM HEAD CAP


    E161700
  1. Attach the claw to install the rear wiper head cap.



13. INSTALL BACK DOOR NO. 2 SERVICE HOLE COVER


B190525
  1. Attach the 2 clips to install the back door No. 2 service hole cover with the 3 screws.



14. INSTALL MULTIPLEX NETWORK BODY ECU (w/ Power Back Door)


B194490
  1. Install the multiplex network body ECU with the 2 screws.

  1. Connect the 2 connector and attach the 2 clamps.



15. INSTALL BACK DOOR SERVICE HOLE COVER


B190522
  1. Apply butyl tape to the door panel, then install a new back door service hole cover as shown in the illustration.

    HINT:
    1. There should be no wrinkles or folds after attaching the service hole cover.
    2. After attaching the service hole cover, check the quality of the seal.



16. INSTALL BACK DOOR TRIM BOARD ASSEMBLY


B190520
  1. Attach the 11 clips to install the back door trim board assembly.



17. INSTALL BACK DOOR PULL STRAP


B190519
  1. Install the back door pull strap with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



18. INSTALL BACK DOOR STRAP COVER


B195035
  1. Attach the claw to slid the back door strap cover as shown in the illustration, and install it.



19. INSTALL BACK DOOR SIDE GARNISH LH


B190516
  1. Attach the 3 clips to install the back door side garnish LH.



20. INSTALL BACK DOOR SIDE GARNISH RH


B190515
  1. Attach the 2 clips to install the back door side garnish RH.



21. INSTALL BACK DOOR CENTER GARNISH


B190514
  1. Attach the 4 clips and the claw to install the back door center garnish.