Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR POWER WINDOW MOTOR

BACK DOOR POWER WINDOW MOTOR > REMOVAL

for Preparation Click here



1. REMOVE BACK DOOR CENTER GARNISH


    B190514
  1. Detach the 4 clips and the claw and remove the back door center garnish.



2. REMOVE BACK DOOR SIDE GARNISH RH


    B190515
  1. Detach the 2 clips and remove the back door side garnish RH.



3. REMOVE BACK DOOR SIDE GARNISH LH


    B190516
  1. Detach the 3 clips and remove the back door side garnish LH



4. REMOVE BACK DOOR STRAP COVER


    B190517
  1. Slide the back door strap cover and detach the claw and remove the back door strap cover.



5. REMOVE BACK DOOR PULL STRAP


    B190519
  1. Remove the bolt and remove the back door pull strap.



6. REMOVE BACK DOOR TRIM BOARD ASSEMBLY


    B190520
  1. Detach the 11 clips and remove the back door trim board assembly.



7. REMOVE BACK DOOR SERVICE HOLE COVER


    B190521
  1. Remove the back door service hole cover.

    NOTICE:
    Remove any tape remaining on the door.



8. REMOVE MULTIPLEX NETWORK BODY ECU (w/ Power Back Door)


    B194490
  1. Disconnect the 2 connectors and detach the 2 clamps.

  1. Remove the 2 screws and remove the multiplex network body ECU.



9. REMOVE BACK DOOR NO. 2 SERVICE HOLE COVER


    B190525
  1. Remove the 3 screws and detach the 2 clips and remove the back door No. 2 service hole cover.



10. REMOVE REAR WIPER ARM HEAD CAP


    E161700
  1. Detach the claw and remove the rear wiper arm head cap.



11. REMOVE REAR WIPER BLADE ASSEMBLY


    E161701
  1. Remove the nut and remove the rear wiper blade assembly.



12. REMOVE REAR WIPER MOTOR ASSEMBLY


    E161698
  1. Detach the clamp and disconnect the connector.

  1. Loosen the 3 bolts and remove the rear wiper motor.

    NOTICE:
    Do not try to remove the bolts since they are integrated with the motor.



13. REMOVE REAR WIPER MOTOR GROMMET


    E161696
  1. Remove the rear wiper motor grommet.



14. REMOVE REAR WIPER STOPPER


    B190526
  1. Detach the claw and guide, and remove the linear wiper step RH.



15. REMOVE BACK DOOR OUTSIDE MOULDING LH


    B191708
  1. Detach the 5 clips and remove the back door outside moulding.



16. REMOVE BACK DOOR OUTSIDE MOULDING RH

HINT:
Use the same procedure as for the LH side.



17. REMOVE BACK DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B195691E01
  1. Apply protective tape to the door panel in the area around the back door glass outer weatherstrip.



    B195692E01
  1. Using a moulding remover, detach the 9 claws and remove the back door glass outer weatherstrip.



18. REMOVE BACK DOOR GLASS RUN


    B190527
  1. Remove the back door glass run.



19. REMOVE BACK DOOR GLASS


    B190513
  1. Remove the hole plug.

  1. Provisionally install the multiplex network body ECU.



    B190528
  1. Move the back door glass until the 4 bolts can be seen through the service holes.

  1. Disconnect the 2 connectors.

  1. Remove the 4 bolts and remove the back door glass.

    NOTICE:
    Do not drop or damage the back door glass.

  1. Remove the multiplex network body ECU.



20. REMOVE BACK DOOR POWER WINDOW REGULATOR ASSEMBLY


    B190529E01
  1. Disconnect the connector.

  1. Loosen nut A.

  1. Remove the 5 nuts, then remove the back door power window regulator assembly.

    NOTICE:
    Do not drop or damage the back door power window regulator assembly when removing the nuts.



21. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


    B194350
  1. Remove the 3 nuts and power window regulator motor.



    B191733
  1. Remove the 2 screws and power window regulator base plate.



    B191734
  1. Using needle nose pliers, remove the drum and wire guide from the motor.

    NOTICE:
    Do not use a screwdriver, etc. when removing them.