BACK DOOR POWER WINDOW MOTOR > REMOVAL |
| 1. REMOVE BACK DOOR CENTER GARNISH |
![]() |
Detach the 4 clips and the claw and remove the back door center garnish.
| 2. REMOVE BACK DOOR SIDE GARNISH RH |
![]() |
Detach the 2 clips and remove the back door side garnish RH.
| 3. REMOVE BACK DOOR SIDE GARNISH LH |
![]() |
Detach the 3 clips and remove the back door side garnish LH
| 4. REMOVE BACK DOOR STRAP COVER |
![]() |
Slide the back door strap cover and detach the claw and remove the back door strap cover.
| 5. REMOVE BACK DOOR PULL STRAP |
![]() |
Remove the bolt and remove the back door pull strap.
| 6. REMOVE BACK DOOR TRIM BOARD ASSEMBLY |
![]() |
Detach the 11 clips and remove the back door trim board assembly.
| 7. REMOVE BACK DOOR SERVICE HOLE COVER |
![]() |
Remove the back door service hole cover.
| 8. REMOVE MULTIPLEX NETWORK BODY ECU (w/ Power Back Door) |
![]() |
Disconnect the 2 connectors and detach the 2 clamps.
Remove the 2 screws and remove the multiplex network body ECU.
| 9. REMOVE BACK DOOR NO. 2 SERVICE HOLE COVER |
![]() |
Remove the 3 screws and detach the 2 clips and remove the back door No. 2 service hole cover.
| 10. REMOVE REAR WIPER ARM HEAD CAP |
![]() |
Detach the claw and remove the rear wiper arm head cap.
| 11. REMOVE REAR WIPER BLADE ASSEMBLY |
![]() |
Remove the nut and remove the rear wiper blade assembly.
| 12. REMOVE REAR WIPER MOTOR ASSEMBLY |
![]() |
Detach the clamp and disconnect the connector.
Loosen the 3 bolts and remove the rear wiper motor.
| 13. REMOVE REAR WIPER MOTOR GROMMET |
![]() |
Remove the rear wiper motor grommet.
| 14. REMOVE REAR WIPER STOPPER |
![]() |
Detach the claw and guide, and remove the linear wiper step RH.
| 15. REMOVE BACK DOOR OUTSIDE MOULDING LH |
![]() |
Detach the 5 clips and remove the back door outside moulding.
| 16. REMOVE BACK DOOR OUTSIDE MOULDING RH |
| 17. REMOVE BACK DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY |
![]() |
Apply protective tape to the door panel in the area around the back door glass outer weatherstrip.
![]() |
Using a moulding remover, detach the 9 claws and remove the back door glass outer weatherstrip.
| 18. REMOVE BACK DOOR GLASS RUN |
![]() |
Remove the back door glass run.
| 19. REMOVE BACK DOOR GLASS |
![]() |
Remove the hole plug.
Provisionally install the multiplex network body ECU.
![]() |
Move the back door glass until the 4 bolts can be seen through the service holes.
Disconnect the 2 connectors.
Remove the 4 bolts and remove the back door glass.
Remove the multiplex network body ECU.
| 20. REMOVE BACK DOOR POWER WINDOW REGULATOR ASSEMBLY |
![]() |
Disconnect the connector.
Loosen nut A.
Remove the 5 nuts, then remove the back door power window regulator assembly.
| 21. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH |
![]() |
Remove the 3 nuts and power window regulator motor.
![]() |
Remove the 2 screws and power window regulator base plate.
![]() |
Using needle nose pliers, remove the drum and wire guide from the motor.