Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)

REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) > DISASSEMBLY

for Preparation Click here


NOTICE:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH


    B193994
  1. Remove the 2 clips.



    B193995
  1. Remove the bolt and rear No. 2 seat inner belt assembly.



2. REMOVE REAR SEAT LOCK COVER OUTER LH


    B193996
  1. Remove the screw.

  1. Detach the 2 claws and remove the rear seat lock cover outer.



3. REMOVE REAR SEAT LOCK COVER INNER RH


    B193998
  1. Remove the screw.

  1. Detach the 3 claws and remove the rear seat lock cover inner.



4. REMOVE REAR NO. 2 SEAT CUSHION ASSEMBLY LH


    B194000
  1. Remove the 2 bolts.

  1. Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts and 2 bushes. Then remove the rear No. 2 seat cushion assembly.



5. REMOVE NO. 3 SEAT CUSHION SPRING ASSEMBLY LH


    B194001
  1. Remove the 7 hog rings.



    B194003
  1. Remove the hooks and No. 3 seat cushion spring.



6. REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH


    B194004
  1. Remove the 13 hog rings and No. 2 seat cushion cover.



7. REMOVE REAR SEAT CUSHION COVER LH


    B194006
  1. Remove the screw.

  1. Detach the claw and remove the rear seat cushion cover.



8. REMOVE REAR SEAT CUSHION COVER INNER RH


    B194007
  1. Remove the screw.

  1. Detach the claw and remove the rear seat cushion cover.



9. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY


10. REMOVE REAR SEAT HEADREST ASSEMBLY


11. REMOVE REAR NO. 2 SEATBACK COVER LH


    B195227
  1. Detach the 3 claws and remove the rear No. 2 seatback cover.



12. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH


    B194009
  1. Detach the 12 clips and remove the rear seatback board.



13. REMOVE REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY


    B194014
  1. Detach the 8 claws and remove the 4 rear No. 2 seat headrest supports.



14. REMOVE SEATBACK COVER WITH PAD


    B194021
  1. Detach the 2 wire harness clamps.

  1. Detach the hooks and remove the seatback cover with pad.



    B194019
  1. Remove the clip and rear seat belt hook.

  1. Remove the hog ring and seatback cover with pad.



15. REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY LH


    B194022
  1. Remove the 16 hog rings and No. 2 seatback cover from the seatback cover.



16. REMOVE REAR SEAT WIRE HARNESS NO. 2


    B222151
  1. Disconnect the 3 connectors.

  1. Detach the 5 wire harness clamps and remove the rear seat wire harness No. 2.



17. REMOVE RECLINING CONTROL BASE LH


    B194027
  1. Remove the 2 nuts and reclining control base.



18. REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH


    B194028
  1. Remove the 3 bolts and No. 3 seatback frame.



19. REMOVE POWER SEAT MOTOR ASSEMBLY RH


    B194029
  1. Using a screwdriver, remove the 2 washers.

    HINT:
    Tape the screwdriver tip before use.



    B201579
  1. Using a screwdriver and hammer, lightly tap the reclining connecting pipe to remove it.



    B191242
  1. Remove the 3 bolts and power seat motor.



20. REMOVE POWER SEAT MOTOR ASSEMBLY LH


    B191243
  1. Remove the 3 bolts and power seat motor.



21. REMOVE REAR NO. 2 SEAT ROD SUB-ASSEMBLY


    B194032
  1. Remove the 2 bolts and No. 2 seat rod.