REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) > REASSEMBLY |
| 1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY |
![]() |
Install the No. 2 seat rod with the 2 bolts.
| 2. INSTALL POWER SEAT MOTOR ASSEMBLY LH |
![]() |
Fully rotate both lower arms in the seat-folded direction, as shown in the illustration.
![]() |
Install the power seat motor with the 3 bolts.
| 3. INSTALL POWER SEAT MOTOR ASSEMBLY RH |
![]() |
Install the power seat motor with the 3 bolts.
![]() |
Using a screwdriver and hammer, lightly tap the reclining connecting pipe to install it.
Install the 2 washers.
![]() |
Hold the reclining connecting pipe with pliers or similar tool and rotate the reclining connecting pipe and arms to the position shown in the illustration.
| 4. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH |
![]() |
Install the No. 3 seatback frame with the 3 bolts.
| 5. INSTALL RECLINING CONTROL BASE LH |
![]() |
Install the reclining control base with the 2 nuts.
| 6. INSTALL REAR SEAT WIRE HARNESS NO. 2 |
![]() |
Attach the 5 wire harness clamps.
Connect the 3 connectors to install the rear seat wire harness No. 2.
| 7. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH |
![]() |
Using hog ring pliers, install the No. 2 seatback cover to the seatback cover with 16 new hog rings.
| 8. INSTALL SEATBACK COVER WITH PAD |
![]() |
Attach the clip to install the rear seat belt hook.
Using hog ring pliers, install the seatback cover with pad to the seatback frame with a new hog ring.
![]() |
Attach the hooks to install the seatback cover with pad.
Attach the 2 wire harness clamps.
| 9. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Align the protruding portion of the rear No. 2 seat headrest supports with the installation grooves of the rear No. 2 seatback frame.
Attach the 8 claws to install the 4 rear No. 2 seat headrest supports.
| 10. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH |
![]() |
Attach the 12 clips to install the rear seatback board.
| 11. INSTALL REAR NO. 2 SEATBACK COVER LH |
![]() |
Attach the 3 claws to install the rear No. 2 seatback cover.
| 12. INSTALL REAR SEAT HEADREST ASSEMBLY |
| 13. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
| 14. INSTALL REAR SEAT CUSHION COVER LH |
![]() |
Attach the claw to install the rear seat cushion cover.
Install the screw.
| 15. INSTALL REAR SEAT CUSHION COVER INNER RH |
![]() |
Attach the claw to install the rear seat cushion cover.
Install the screw.
| 16. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH |
![]() |
Using hog ring pliers, install the No. 2 seat cushion cover to the seat cushion pad with 13 new hog rings.
| 17. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY LH |
![]() |
Attach the hooks.
![]() |
Using hog ring pliers, install the No. 3 seat cushion spring to the seat cushion cover with 7 new hog rings.
| 18. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH |
![]() |
Install the 2 bushes to the cushion spring. Then using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.
Install the 2 bolts.
| 19. INSTALL REAR SEAT LOCK COVER OUTER LH |
![]() |
Attach the 2 claws to install the rear seat lock cover outer.
Install the screw.
| 20. INSTALL REAR SEAT LOCK COVER INNER RH |
![]() |
Attach the 3 claws to install the rear seat lock cover inner.
Install the screw.
| 21. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH |
![]() |
Install the rear No. 2 seat inner belt assembly with the bolt.
![]() |
Install the 2 clips.