REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) > REASSEMBLY |
| 1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY |
![]() |
Install the rear No. 2 seat rod sub-assembly with the 2 bolts.
| 2. INSTALL POWER SEAT MOTOR ASSEMBLY LH |
![]() |
Fully rotate both lower arms in the seat folded direction as shown in the illustration.
![]() |
Install the power seat motor assembly LH with the 3 bolts.
| 3. INSTALL POWER SEAT MOTOR ASSEMBLY RH |
![]() |
Install the power seat motor assembly RH with the 3 bolts.
![]() |
Using a screwdriver and hammer, lightly tap the reclining connecting pipe to install it.
Install the 2 washers.
![]() |
Hold the reclining connecting pipe with pliers or similar tool and rotate the reclining connecting pipe and arms to the position shown in the illustration.
| 4. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH |
![]() |
Install the No. 3 seatback frame sub-assembly LH with the 3 bolts.
| 5. INSTALL RECLINING CONTROL BASE LH |
![]() |
Install the reclining control base LH with the 2 nuts.
| 6. INSTALL REAR NO. 2 SEAT WIRE LH |
![]() |
Attach the 5 wire harness clamps.
Connect the 3 connectors to install the rear No. 2 seat wire LH.
| 7. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH |
![]() |
Using hog ring pliers, install the No. 2 seatback cover sub-assembly LH to the No. 2 seatback pad with new hog rings.
| 8. INSTALL SEATBACK COVER WITH PAD |
![]() |
Attach the clip to install the rear seat belt hook.
Using hog ring pliers, install the seatback cover with pad to the No. 3 seatback frame sub-assembly LH with a new hog ring.
![]() |
Attach the hooks.
Attach the 2 wire harness clamps.
| 9. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Attach the 8 claws to install the 4 rear No. 2 seat headrest supports.
| 10. INSTALL REAR SEAT HEADREST ASSEMBLY |
![]() |
Install the rear seat headrest assembly.
![]() |
Insert the cable end into the reclining control base LH.
Twist the cable end in the direction indicated by the arrow to connect it and attach the cable clamp.
Connect the headrest cable to the No. 3 seatback frame sub-assembly LH with the cable clamp.
![]() |
Attach the hook to connect the lower part of the No. 2 seatback cover sub-assembly LH.
| 11. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH |
![]() |
Attach the 12 clips to install the rear seatback board sub-assembly LH.
| 12. INSTALL REAR NO. 2 SEATBACK COVER LH |
![]() |
Attach the 3 claws to install the rear No. 2 seatback cover LH.
| 13. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
Install the rear center seat headrest assembly.
| 14. INSTALL REAR SEAT CUSHION COVER LH |
![]() |
Attach the claw.
Install the rear seat cushion cover LH with the screw.
| 15. INSTALL REAR SEAT CUSHION COVER INNER RH |
![]() |
Attach the claw.
Install the rear seat cushion cover inner RH with the screw.
| 16. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH |
![]() |
Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion pad with new hog rings.
| 17. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY LH |
![]() |
Set the No. 3 seat cushion spring assembly LH in place.
Attach the hooks.
![]() |
Using hog ring pliers, install the No. 3 seat cushion spring assembly LH with new hog rings.
| 18. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH |
![]() |
Install the 2 bushes to the No. 3 seat cushion spring assembly LH. Then using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.
Install the rear No. 2 seat cushion assembly LH with the 2 bolts.
| 19. INSTALL REAR SEAT LOCK COVER OUTER LH |
![]() |
Attach the 2 claws.
Install the rear seat lock cover outer LH with the screw.
| 20. INSTALL REAR SEAT LOCK COVER INNER RH |
![]() |
Attach the 3 claws.
Install the rear seat lock cover inner RH with the screw.
| 21. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH |
![]() |
Install the rear No. 2 seat inner belt assembly with the bolt.
![]() |
Install the 2 clips.