Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side)

REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side) > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH


    B193994
  1. Remove the 2 clips.



    B193995
  1. Remove the bolt and rear No. 2 seat inner belt assembly.



2. REMOVE REAR SEAT LOCK COVER OUTER LH


    B193996
  1. Remove the screw.

  1. Detach the 2 claws and remove the rear seat lock cover outer LH.



3. REMOVE REAR SEAT LOCK COVER INNER RH


    B193998
  1. Remove the screw.

  1. Detach the 3 claws and remove the rear seat lock cover inner RH.



4. REMOVE REAR NO. 2 SEAT CUSHION ASSEMBLY LH


    B194000
  1. Remove the 2 bolts.

  1. Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts and 2 bushes. Then remove the rear No. 2 seat cushion assembly LH.



5. REMOVE NO. 3 SEAT CUSHION SPRING ASSEMBLY LH


    B194001
  1. Remove the hog rings.



    B194003
  1. Detach the hooks and remove the No. 3 seat cushion spring assembly LH.



6. REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH


    B194004
  1. Remove the hog rings and No. 2 seat cushion cover sub-assembly LH from the No. 2 seat cushion pad.



7. REMOVE REAR SEAT CUSHION COVER LH


    B194006
  1. Remove the screw.

  1. Detach the claw and remove the rear seat cushion cover LH.



8. REMOVE REAR SEAT CUSHION COVER INNER RH


    B194007
  1. Remove the screw.

  1. Detach the claw and remove the rear seat cushion cover inner RH.



9. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY
  1. Remove the rear center seat headrest assembly.



10. REMOVE REAR SEAT HEADREST ASSEMBLY


B288883E01
  1. Using a screwdriver, push in the headrest lock button to release the headrest lock.

    HINT:
    Tape the screwdriver tip before use.

  1. Pull up and remove the rear seat headrest assembly.

    NOTICE:
    When removing the rear seat headrest assembly while it is in the vehicle, fold down the headrest before removing it so that it does not contact the roof.



11. REMOVE REAR NO. 2 SEAT HANDLE


    B191219
  1. Remove the 2 screws.

  1. Disconnect the rear No. 1 seat lock cable assembly and remove the rear No. 2 seat handle.



12. REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B194008
  1. Remove the screw.

  1. Disconnect the rear No. 1 seat lock cable assembly and remove the rear back lock control lever sub-assembly RH.



13. REMOVE REAR NO. 2 SEATBACK COVER LH


    B195227
  1. Detach the 3 claws and remove the rear No. 2 seatback cover LH.



14. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH


    B292870
  1. Detach the 12 clips and remove the rear seatback board sub-assembly LH.



15. REMOVE REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY


    B290095
  1. Detach the 8 claws and remove the 4 rear No. 2 seat headrest supports.



16. REMOVE SEATBACK COVER WITH PAD


    B195218
  1. Detach the hooks.



    B293202
  1. Detach the hooks.



    B194019
  1. Remove the clip and rear seat belt hook.

  1. Remove the hog ring and seatback cover with pad.



17. REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY LH


    B194022
  1. Remove the hog rings and No. 2 seatback cover sub-assembly LH from the No. 2 seatback pad.



18. REMOVE REAR SEAT RECLINING COVER INNER LH


    B194025
  1. Remove the screw.

  1. Detach the claw and remove the rear seat reclining cover inner LH.



19. REMOVE REAR SEAT RECLINING COVER INNER RH


    B194026
  1. Remove the screw.

  1. Detach the claw and remove the rear seat reclining cover inner RH.



20. REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY


    B293203
  1. Detach the 3 cable ties.

  1. Disconnect the 2 clamps.

  1. Rotate the cable ends.

  1. Pull the cable through the No. 3 seatback frame sub-assembly and remove the rear No. 1 seat lock cable assembly.



21. REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH


    B293204
  1. Remove the 5 bolts and No. 3 seatback frame sub-assembly LH.



22. REMOVE REAR NO. 2 SEAT ROD SUB-ASSEMBLY


    B194032
  1. Remove the 2 bolts and rear No. 2 seat rod sub-assembly.