Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side)

REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side) > REASSEMBLY

for Preparation Click here


NOTICE:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY


    B194032
  1. Install the No. 2 seat rod with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



2. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH


    B194031
  1. Install the No. 3 seatback frame with the 5 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



3. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY


    B194030
  1. Insert the cable through the No. 3 seatback frame.

  1. Insert and rotate the cable ends to connect them.

  1. Connect the 2 clamps.

  1. Install the cable with the 3 cable ties.



4. INSTALL REAR SEAT RECLINING COVER INNER LH


    B194025
  1. Attach the claw to install the rear seat reclining cover.

  1. Install the screw.



5. INSTALL REAR SEAT RECLINING COVER INNER RH


    B194026
  1. Attach the claw to install the rear seat reclining cover.

  1. Install the screw.



6. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH


    B194023E02
  1. Using hog ring pliers, install the No. 2 seatback cover to the seatback pad with 16 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



7. INSTALL SEATBACK COVER WITH PAD


    B194020E02
  1. Install the rear seat belt hook with the clip.

  1. Using hog ring pliers, install the seatback cover with pad to the seatback frame with a new hog ring.



    B194018
  1. Attach the hooks to install the seatback cover with pad.



    B195218
  1. Attach the hooks.



8. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY


    B194017E01
  1. Align the protruding portion of the rear No. 2 seat headrest supports with the installation grooves of the rear No. 2 seatback frame.

  1. Attach the 8 claws to install the 2 rear No. 2 seat headrest supports.



9. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH


    B194010
  1. Attach the 12 clips to install the rear seatback board.



10. INSTALL REAR NO. 2 SEATBACK COVER LH


    B195227
  1. Attach the 3 claws to install the rear No. 2 seatback cover.



11. INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B194008E01
  1. Connect the cable in the order shown in the illustration to install the rear back lock control lever.

  1. Install the rear back lock control lever with the screw.



12. INSTALL REAR NO. 2 SEAT HANDLE


    B191219E01
  1. Connect the cable in the order shown in the illustration to install the rear No. 2 seat handle.

  1. Install the rear No. 2 seat handle with the 2 screws.



13. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


14. INSTALL REAR SEAT HEADREST ASSEMBLY


15. INSTALL REAR SEAT CUSHION COVER LH


    B194006
  1. Attach the claw to install the rear seat cushion cover.

  1. Install the screw.



16. INSTALL REAR SEAT CUSHION COVER INNER RH


    B194007
  1. Attach the claw to install the rear seat cushion cover.

  1. Install the screw.



17. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH


    B194005E02
  1. Using hog ring pliers, install the No. 2 seat cushion cover to the seat cushion pad with 13 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



18. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY LH


    B194003
  1. Attach the hooks.



    B194002E02
  1. Using hog ring pliers, install the No. 3 seat cushion spring to the seat cushion cover with 7 new hog rings.



19. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH


B194000E01
  1. Install the 2 bushes to the cushion spring. Then using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.

    1. for bolt A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Install the 2 bolts.

    1. for bolt B

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



20. INSTALL REAR SEAT LOCK COVER OUTER LH


    B193996
  1. Attach the 2 claws to install the rear seat lock cover outer.

  1. Install the screw.



21. INSTALL REAR SEAT LOCK COVER INNER RH


    B193998
  1. Attach the 3 claws to install the rear seat lock cover inner.

  1. Install the screw.



22. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH


    B193995
  1. Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193994
  1. Install the 2 clips.