Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side)

REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side) > REASSEMBLY

for Preparation Click here


NOTICE:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY


    B194032
  1. Install the rear No. 2 seat rod sub-assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



2. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH


    B293204
  1. Install the No. 3 seatback frame sub-assembly LH with the 5 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



3. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY


    B293203
  1. Insert the rear No. 1 seat lock cable assembly through the No. 3 seatback frame sub-assembly.

  1. Insert and rotate the cable ends to connect them.

  1. Connect the 2 clamps.

  1. Attach the 3 cable ties to install the rear No. 1 seat lock cable assembly.



4. INSTALL REAR SEAT RECLINING COVER INNER LH


    B194025
  1. Attach the claw.

  1. Install the rear seat reclining cover inner LH with the screw.



5. INSTALL REAR SEAT RECLINING COVER INNER RH


    B194026
  1. Attach the claw.

  1. Install the rear seat reclining cover inner RH with the screw.



6. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH


    B194023E01
  1. Using hog ring pliers, install the No. 2 seatback cover sub-assembly LH to the No. 2 seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



7. INSTALL SEATBACK COVER WITH PAD


    B194020E01
  1. Attach the clip to install the rear seat belt hook.

  1. Using hog ring pliers, install the seatback cover with pad to the seatback frame with a new hog ring.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B293202
  1. Attach the hooks.



    B195218
  1. Attach the hooks.



8. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY


B290086
  1. Attach the 8 claws to install the 4 rear No. 2 seat headrest supports.



9. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH


    B292870
  1. Attach the 12 clips to install the rear seatback board sub-assembly LH.



10. INSTALL REAR NO. 2 SEATBACK COVER LH


    B195227
  1. Attach the 3 claws to install the rear No. 2 seatback cover LH.



11. INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B194008E01
  1. Connect the rear No. 1 seat lock cable assembly in the order shown in the illustration to install the rear back lock control lever sub-assembly RH.

  1. Install the rear back lock control lever sub-assembly RH with the screw.



12. INSTALL REAR NO. 2 SEAT HANDLE


    B191219E01
  1. Connect the rear No. 1 seat lock cable assembly to the rear No. 2 seat handle in the order shown in the illustration.

  1. Install the rear No. 2 seat handle with the 2 screws.



13. INSTALL REAR SEAT HEADREST ASSEMBLY


B290078
  1. Install the rear seat headrest assembly.

    NOTICE:
    1. Make sure the rear seat headrest assembly is facing in the correct direction.
    2. Push in the rear seat headrest assembly until the headrest lock engages.



14. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
  1. Install the rear center seat headrest assembly.



15. INSTALL REAR SEAT CUSHION COVER LH


    B194006
  1. Attach the claw.

  1. Install the rear seat cushion cover LH with the screw.



16. INSTALL REAR SEAT CUSHION COVER INNER RH


    B194007
  1. Attach the claw.

  1. Install the rear seat cushion cover inner RH with the screw.



17. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH


    B194005E01
  1. Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



18. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY LH


    B194003
  1. Set the No. 3 seat cushion spring assembly LH in place.

  1. Attach the hooks.



    B194002E01
  1. Using hog ring pliers, install the No. 3 seat cushion spring assembly LH with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



19. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH


B194000
  1. Install the 2 bushes to the No. 3 seat cushion spring assembly LH. Then using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the rear No. 2 seat cushion assembly LH with the 2 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



20. INSTALL REAR SEAT LOCK COVER OUTER LH


    B193996
  1. Attach the 2 claws.

  1. Install the rear seat lock cover outer LH with the screw.



21. INSTALL REAR SEAT LOCK COVER INNER RH


    B193998
  1. Attach the 3 claws.

  1. Install the rear seat lock cover inner RH with the screw.



22. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH


    B193995
  1. Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193994
  1. Install the 2 clips.