Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type RH Side)

REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type RH Side) > DISASSEMBLY

for Preparation Click here


NOTICE:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. REMOVE REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY


    B191205
  1. Remove the 2 clips.



    B191206
  1. Remove the bolt and rear No. 2 seat inner belt sub-assembly.



2. REMOVE REAR SEAT LOCK COVER INNER LH


    B191207
  1. Remove the screw.

  1. Detach the 3 claws and remove the rear seat lock cover inner LH.



3. REMOVE REAR SEAT LOCK COVER OUTER RH


    B191209
  1. Remove the screw.

  1. Detach the 2 claws and remove the rear seat lock cover outer RH.



4. REMOVE REAR NO. 2 SEAT CUSHION ASSEMBLY RH


    B191211
  1. Remove the 2 bolts.

  1. Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts and 2 bushes. Then remove the rear No. 2 seat cushion assembly LH.



5. REMOVE NO. 3 SEAT CUSHION SPRING ASSEMBLY RH


    B191212
  1. Remove the hog rings.



    B191214
  1. Detach the hooks and No. 3 seat cushion spring assembly RH.



6. REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH


    B191215
  1. Remove the hog rings and No. 2 seat cushion cover sub-assembly RH from the No. 2 seat cushion pad.



7. REMOVE REAR SEAT CUSHION COVER LH


    B191218
  1. Remove the screw.

  1. Detach the claw and remove the rear seat cushion cover LH.



8. REMOVE REAR SEAT CUSHION COVER OUTER RH


    B191217
  1. Remove the screw.

  1. Detach the claw and remove the rear seat cushion cover outer RH.



9. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH


    B290083
  1. Detach the 9 clips and remove the rear seatback board sub-assembly RH.



10. REMOVE REAR SEAT HEADREST ASSEMBLY


B288867
  1. Detach the hook and disconnect the lower part of the No. 2 seatback cover sub-assembly RH.



    B288831E01
  1. Remove the cable clamp and disconnect the headrest cable from the No. 3 seatback frame sub-assembly RH.

  1. Detach the cable clamp, twist the cable end in the direction indicated by the arrow and disconnect the headrest cable from the reclining control base RH.



    B288882E01
  1. Using a screwdriver, push in the headrest lock button to release the headrest lock.

    HINT:
    Tape the screwdriver tip before use.

  1. Pull up and remove the rear seat headrest assembly.

    NOTICE:
    When removing the rear seat headrest assembly while it is in the vehicle, fold down the headrest before removing it so that it does not contact the roof.



11. REMOVE REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY


    B290087
  1. Detach the 4 claws and remove the 2 rear No. 2 seat headrest supports.



12. REMOVE SEATBACK COVER WITH PAD


    B288986
  1. Detach the 2 wire harness clamps.

  1. Detach the hooks and remove the seatback cover with pad.



13. REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY RH


    B191231
  1. Remove the hog rings and No. 2 seatback cover sub-assembly from the No. 2 seatback pad.



14. REMOVE REAR NO. 2 SEAT WIRE RH


    B191237
  1. Disconnect the 3 connectors.

  1. Detach the 4 wire harness clamps and remove the rear No. 2 seat wire RH.



15. REMOVE RECLINING CONTROL BASE RH


    B195223
  1. Remove the 2 nuts and reclining control base RH.



16. REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY RH


    B191239
  1. Remove the 3 bolts and No. 3 seatback frame sub-assembly RH.



17. REMOVE POWER SEAT MOTOR ASSEMBLY RH


    B191241E01
  1. Using a screwdriver, remove the 2 washers.



    B201585
  1. Using a screwdriver and hammer, lightly tap the reclining connecting pipe to remove it.



    B191242
  1. Remove the 3 bolts and power seat motor assembly RH.



18. REMOVE POWER SEAT MOTOR ASSEMBLY LH


    B191243
  1. Remove the 3 bolts and power seat motor assembly LH.



19. REMOVE REAR NO. 2 SEAT ROD SUB-ASSEMBLY


    B191244
  1. Remove the 2 bolts and rear No. 2 seat rod sub-assembly.