Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type RH Side)

REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type RH Side) > REASSEMBLY

for Preparation Click here


NOTICE:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY


    B191244
  1. Install the No. 2 seat rod with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



2. INSTALL POWER SEAT MOTOR ASSEMBLY LH


    B201586
  1. Fully rotate both lower arms in the seat-folded direction, as shown in the illustration.

    NOTICE:
    If the motor is installed with the lower arms at an intermediate position, the motor initial position will not match the seat position, so that when the seat is operated the position will be incorrect.



    B201581
  1. Install the power seat motor with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



3. INSTALL POWER SEAT MOTOR ASSEMBLY RH


    B201582
  1. Install the power seat motor with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    B201587
  1. Using a screwdriver and hammer, lightly tap the reclining connecting pipe to install it.

  1. Install the 2 washers.

    NOTICE:
    When the reclining connecting pipe extends about the same distance left and right, install the 2 washers.



    B201588
  1. Hold the reclining connecting pipe with pliers or similar tool and rotate the reclining connecting pipe and arms to the position shown in the illustration.



4. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY RH


    B191239
  1. Install the No. 3 seatback frame with the 5 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



5. INSTALL RECLINING CONTROL BASE RH


    B195223
  1. Install the reclining control base with the 2 nuts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



6. INSTALL REAR SEAT WIRE HARNESS NO. 2


    B191237
  1. Attach the 4 wire harness clamps.

  1. Connect the 3 connectors to install the rear seat wire harness No. 2.



7. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY RH


    B191232E02
  1. Using hog ring pliers, install the No. 2 seatback cover to the seatback pad with 13 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



8. INSTALL SEATBACK COVER WITH PAD


    B191230
  1. Attach the hooks to install the seatback cover with pad.

  1. Attach the 2 wire harness clamps.



9. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY


    B191226E01
  1. Align the protruding portion of the rear No. 2 seat headrest supports with the installation grooves of the rear No. 2 seatback frame.

  1. Attach the 4 claws to install the 2 rear No. 2 seat headrest supports.



10. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH


    B191221
  1. Attach the 9 clips to install the rear seatback board.



11. INSTALL REAR SEAT HEADREST ASSEMBLY


12. INSTALL REAR SEAT CUSHION COVER LH


    B191218
  1. Attach the claw to install the rear seat cushion cover.

  1. Install the screw.



13. INSTALL REAR SEAT CUSHION COVER OUTER RH


    B191217
  1. Attach the claw to install the rear seat cushion cover.

  1. Install the screw.



14. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH


    B191216E03
  1. Using hog ring pliers, install the No. 2 seat cushion cover to the seat cushion pad with 10 new hog rings

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



15. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY RH


    B191214
  1. Attach the hooks.



    B191213E02
  1. Using hog ring pliers, install the No. 3 seat cushion spring to the seat cushion cover with 5 new hog rings.



16. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY RH


B191211E01
  1. Install the 2 bushes to the cushion spring. Then using a T45 "TORX" socket, install the 2 "TORX" bolts.

    1. for bolt A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Install the 2 bolts.

    1. for bolt B

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



17. INSTALL REAR SEAT LOCK COVER INNER LH


    B191207
  1. Attach the 3 claws to install the rear seat lock cover inner.

  1. Install the screw.



18. INSTALL REAR SEAT LOCK COVER OUTER RH


    B191209
  1. Attach the 2 claws to install the rear seat lock cover outer.

  1. Install the screw.



19. INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY


    B191206
  1. Install the rear No. 2 seat inner belt sub-assembly.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191205
  1. Install the 2 clips.