Home › Vehicle Interior › SEAT BELT › REAR NO. 1 SEAT OUTER BELT ASSEMBLY

REAR NO. 1 SEAT OUTER BELT ASSEMBLY > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the RH side.



1. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat)
  1. Remove the rear No. 2 seat assembly (Click here).



2. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat)
  1. Remove the rear No. 2 seat assembly (Click here).



3. REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH


    B191794
  1. Detach the 2 clips and 5 claws, and remove the rear seat cushion hinge lower cover.



4. REMOVE REAR FLOOR STEP NO. 1 COVER


    B191403E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



5. REMOVE REAR FLOOR STEP NO. 2 COVER


    B193052E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



6. REMOVE REAR DOOR SCUFF PLATE RH


    B186665
  1. Remove the bolt.

  1. Detach the 5 clips, 6 claws and 2 guides, and remove the rear door scuff plate front side.



    B186666
  1. Remove the 2 bolts.

  1. Detach the 5 clips and 2 claws, and remove the scuff plate rear side.



7. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B191804
  1. Remove the rear door opening weatherstrip.



8. REMOVE ROPE HOOK ASSEMBLY

HINT:
Use the same procedure for both sides.



    B190140E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.



    B190141
  1. Remove the bolt and the rope hook.



9. REMOVE REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Detach the 5 clips and 4 claws, and remove the rear floor mat support plate.



10. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Manual Seat)


    B190145
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the connector and remove the quarter trim panel.


    B219907



11. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)


    B190145
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the 3 connectors and remove the quarter trim panel.


    B222459



12. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH


    B190121E02
  1. Using a screwdriver with its tip wrapped in protective tape, detach the claw and remove the cover.



    B190124
  1. Remove the bolt.

  1. Detach the 5 clips.

  1. Pass the rear seat outer belt floor anchor through the rear window side garnish, and remove the rear window side garnish.



13. REMOVE REAR SIDE NO. 2 AIR DUCT


    E181294
  1. Remove the 2 clips and the air duct.



14. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH


    B194784
  1. Remove the nut.



    B194785
  1. Remove the 2 bolts and rear No. 1 seat outer belt assembly.



15. REMOVE REAR NO. 1 SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    B194786
  1. Remove the 2 bolts and rear No. 1 shoulder belt anchor adjuster assembly.